Galaxy Aqua 4000 Kurulum Talimatları Kılavuzu - Sayfa 3
Sıhhi Tesisat Ürünleri Galaxy Aqua 4000 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Galaxy Aqua 4000 6 sayfaları. Electric shower
Sayfayı Yazdır
This appliance is not intended for use
by persons (Including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been
given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to
ensure that they do not play with the
appliance.
3
SECTION
GENERAL LAYOUT OF A
SHOWER INSTALLATION
A TYPICAL INSTANTANEOUS ELECTRIC SHOWER INSTALLATION
Plan your own installation carefully. Check
on the nearest and most readily accessible
rising mains water supply, this may be
beneath the bath or in the loft, where it
feeds the cold water storage tank. Use
only the cold rising water main supply.
Do not connect the shower unit to the
down service from the tank.
Avoid connecting the shower unit, if
possible, were it will be affected by water
drawn off by other appliances, e.g. From
the mains feed to the W.C., This may
cause a drop in pressure too low for the
shower unit to work correctly.
An isolating valve must be fitted into the
water supply for servicing purposes.
4
SECTION
INSTALLATION
Position your shower unit on the wall away
from the direct spray of the shower and at
about the same height as the shower head
position.
The shower unit should be positioned so
that the shower head cannot be immersed
in the bath or shower tray when hanging
down.
LOW
AUTO
Aqua
000
PRESSURE
RESET
COLD
LOW
HIGH
STOP
5
6
4
7
3
8
2
9
1
10
TEMPERATURE
Remove the two screws securing the
shower unit cover and remove the cover
complete with the control knobs.
Place the shower unit on the wall and mark
the location of the fixing screws through the
back plate.
Carefully drill the holes as marked using a
sharpe 5.5mm masonry drill.
Fix the shower unit to the wall using the
plugs and screws provided, do not fully
tighten at this stage.
IMPORTANT
To comply with National Water Council
bylaws a double check valve must be
fitted with all flexible shower accessories
where it is possible that the shower head
may come into contact with used water
i.e. In the bath or shower tray.
5
SECTION
PLUMBING CONNECTION
Plumbing the shower unit must precede
wiring.
Turn off the water supply at the isolating
stop tap.
Having determined the direction of the
inlet water supply: Top (falling), Bottom
(rising), or Back inlet. It is necessary to
remove the appropriate plastic cross
section from the back plate, before
commencing with the installation (See
diagrams Fig 1 & Fig 2).
Remove this plastic
crosssection when
Remove this plastic
using the 'REAR' or
crosssection when
'TOP' entry point for
using the 'BOTTOM'
plumbing.
entry point for plumbing.
Fig 1.
The back plate is fitted with removable
inserts for Top (falling) and Bottom
(rising) inlet mains water pipework to
the shower unit.
We have incorporated into the bottom
right-hand side of the back plate an easy
removable trim section, to allow easy
access when connecting the water supply.
(Please Note! Remember to replace this
trim section before refitting the cover).
.
Connect the mains water supply to the
inlet of the shower unit using a 15mm
copper or stainless pipe with a 15mm
compression elbow or 15mmm push-fit
elbow. Do not use excessive force
when making the connection to the unit.
IMPORTANT
Before turning on the water supply to the
shower unit the water supply pipe should
be flushed out to remove debris. This can
be achieved by connecting the flexible
hose to the 15mm compression elbow and
Fig 2.
turning on the mains water supply long
enough to clear the debris.
After flushing the pipework ensure that the
shower unit is positioned squarely on the