DynaQuip WaterCop Pro Hızlı Başlangıç Kılavuzu

Sıhhi Tesisat Ürünleri DynaQuip WaterCop Pro için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. DynaQuip WaterCop Pro 4 sayfaları.

Sayfayı Yazdır

Before Installing the Valve

1. To mount the valve on the actuator, place the

O-ring on the valve in the circular indentation

around the stem.

2. Use a thin metal object that ﬁ ts in the valve stem

groove to turn the valve and adjust it so that it is

aligned with the actuator.

3. Once the valve is aligned and in place, put the clip

on the four pins such that the curve is on the inside

of all four posts.

4. Make sure the Water Control Panel wiring matches

the wiring guide on page 3. To access the board,

remove the four screws on the front of the Water

Control Panel, remove the bottom and ﬂ ip the front

panel so that the back is facing up.

5. Plug the Water Control Panel into a standard outlet.

KEEP FINGERS AND OTHER OBJECTS AWAY

FROM VALVE TO AVOID INJURY. You should hear

the actuator turn the valve one full cycle.

6. Test the actuator by removing the rubber stops at

both ends of the valve and checking to see the

valve position. The indicator lights on the Water

Control Panel should show the correct current

position of the valve.

7. Change valve position by pressing the UNLIT "OPEN"

or "CLOSE" button. Press the UNLIT indicator, either

"OPEN" or "CLOSE", whichever one does not have

a LIT light next to it to tell the actuator to perform

one-half cycle.

KEEP FINGERS AND OTHER OBJECTS

AWAY FROM VALVE TO AVOID INJURY.

8. Visually verify that the valve has changed position.

9. Repeat steps 10-11 a few times by pressing the

alternating UNLIT button "OPEN" or "CLOSE" to

test and exercise the valve and actuator.

10. You are now ready to install the valve. Please refer

to the "Valve Installation" section of the Instruction

Manual for detailed instructions for various methods

of installation.

The proven leader in household leak protection: WaterCop® is there when you're not.

Quick Start Guide

Installing and Testing Sensors

Hardwired Sensor Probes

1. To install hardwired sensor probes (WPSC), ﬁ rst

ensure that power is disconnected to the Water

Control Panel.

2. Open the case for the Water Control Panel and note

the side circuit board with one long terminal strip

going the full length.

3. Wire the desired number of sensor probes into the

terminal strip matching the leads of the wire with

the paired off terminals as marked by the writing on

the circuit board.

4. If the wires are in the wrong terminals, the sensor

probe will not work.

5. Once you have wired the desired number of sensor

probes into the terminal strip, close the case and

replace the screws.

6. Plug the Water Control Panel into a standard outlet

and wait for it to beep indicating it has ﬁ nished its

boot up sequence.

7. SHORT the sensor probes with a metal object to

have the Water Control Panel recognize them.

The lights will remain on showing which sensor

probes the system recognizes and will ﬂ ash when

something is wrong.

8. Test each sensor probe by shorting it until the

Water Control Panel display shows that the probe

has shorted and then removing the short and

waiting for the display to go back to normal.

(5-10 seconds)

9. Test each sensor probe by getting it wet, checking

that the valve did close and the alarm did sound.

10. Between each sensor probe wet test, ﬁ rst silence

the Water Control Panel AFTER the valve has

ﬁ nished closing by pressing any button once, then

remove the source of wetness and completely dry

off the sensor probe.

11. Press the "OPEN" button once and then wait for

the solid "MODE" light to turn off before pressing

"OPEN" again to open the valve and continue.

12. Repeat steps 8-11 until all sensor probes have

been tested.