DynaQuip Controls WaterCop Kullanım Kılavuzu & Kurulum Kılavuzu - Sayfa 2
Kontrol Ünitesi DynaQuip Controls WaterCop için çevrimiçi göz atın veya pdf Kullanım Kılavuzu & Kurulum Kılavuzu indirin. DynaQuip Controls WaterCop 8 sayfaları. Emergency leak detection and water shut-off system
Sayfayı Yazdırit to be located anywhere a leak is likely to occur, or
where water might cause damage. The WaterCop
requires household electrical power (common 115
VAC, grounded outlet) and will not operate during a
power outage.
Selection of WaterCop
®
The WaterCop
valve should be installed in the main
water line just downstream from the main shut-off valve
in your home. The front control panel of the
®
WaterCop
should be easily visible in order to see
what position the valve is in (open/closed). It should
also be easily accessible for resetting after a leak has
been detected and the water supply has been shut off.
®
While the WaterCop
is completely supported by the
piping in your plumbing system when it is installed,
placement of the valve should ensure that the housing
is protected from use as a step or from other excessive
®
loads. The WaterCop
power, and the provided power cord must be plugged
into a properly grounded power source (115 VAC). Do
not use an extension cord.
The shut-off valve must be
installed indoors
• In the main water line;
• Just downstream from the
• In a dry location;
• Where it is accessible for
• Where the case is protected
Local electrical and plumbing
codes should be consulted to ensure that the
installation is in complete compliance. (See
Installation section for details.)
®
Installation Sites
requires household electrical
main water shut-off valve;
checking and resetting the
valve and for resetting the
radio receiver code, if
necessary;
from use as a step or from
other excessive loads.
Selection of WaterHound Locations
Each WaterCop
WaterHounds. Additional WaterHounds may be added
at any time. A WaterHound consists of a transmitter (a
rectangular box with an antenna) and a sensor (a small
disc at the end of the wire, with two short gold prongs
protruding from one side). The WaterHound should be
placed in locations where leaks are most likely to
occur.
The transmitter in the WaterHound and receiver in
®
WaterCop
communicate by radio frequency. The
smaller the distance between them, the stronger the
signal will be. The maximum transmission distance is
somewhat dependent upon the building layout and
type of construction, but will be in the 150'-200' range.
The WaterHound transmitter (attached to the sensor)
must be kept dry.
WaterHound should never be placed outdoors. The
sensor detects the water from a leak and is completely
waterproof. Sensors should be placed on the floor or in
areas where water would tend to accumulate rapidly in
®
common leak or overflow situations. Make sure that
any water from a leak will drain toward the sensor,
not away from it. Avoid high traffic areas where the
cord or sensor could be stepped on or kicked and
where children or pets may disturb it. The sensor
should be placed FLAT on the floor so water can be
detected as soon as it begins to accumulate. The
sensor may be secured to the floor with adhesive tape.
To avoid damage to transmitters and to provide for the
strongest signal possible, the WaterHound transmitter
should be mounted in a convenient location (on the
wall, in a cabinet, closet, etc.) two to three feet above
the floor (see illustration on page 4). (See Installation
section for details on WaterHound installation
Suggested Locations
Washing Machines
Dishwashers
Kitchen Sinks
Bathroom Sinks
Water Heaters
WaterHound Battery Life
High quality alkaline "AA" batteries are recommended.
Under normal conditions (standby mode) the batteries
should last about one year. Each transmitter has a low
battery signal (audible chirp). Replace batteries at
least annually or when low battery signal is detected.
Re-test each unit in its regular location (see installation
manual). If you are away from home for long periods of
time, transmitters should be tested upon your return to
ensure proper function
Operating the WaterCop
The normal position of the valve is open to allow full
flow throughout the plumbing system. WaterCop
full port ball valve which does not restrict the flow
capacity of your plumbing system. The indicator lights
on the face of the WaterCop
the valve.
If the valve is in the closed position (the red light will be
lit), press "open" and the valve will move to the open
position (green indicator will light).
2
®
can support an unlimited number of
It is NOT splash proof. The
Toilets
Icemakers/Refrigerators
Automatic Humidifiers
Pipes that are prone to
freezing
.
System
®
®
will show the position of
.
)
®
is a