DynaQuip Controls WaterCop Kullanıcı El Kitabı - Sayfa 8

Su Sistemi DynaQuip Controls WaterCop için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. DynaQuip Controls WaterCop 8 sayfaları. Automatic water shut-off systems

Sayfayı Yazdır

Changing Digital Codes

Codes on all control units and transmitters are set at

the factory and should not require alteration. If you use

other wireless products in your home (garage door

openers, etc.), there is a slight chance of interference

with the signal. The following instructions will aid in

resetting the code.

Important Note: All transmitters and the control

unit must have the same code setting!

Changing the receiver code

Disconnect power to receiver unit by unplugging power

cord.

1. Remove cover using the 4 screws located in the

corners of the cover.

2. Locate code switch block (see illustration at right).

Switches are numbered 1 through 6.

3. Arrange the switches in any combination (on or off

position). Write down the code combination you

selected. Example: 1-on, 2-off, 3-off, 4-on, 5-off and

6-on.

4. Reinstall cover. Carefully tuck wires completely into

case and hold cover in position while tightening

screws.

5. Reconnect power by plugging the power cord into

power receptacle.

Changing the transmitter code

1. Remove transmitter cover (loosen two screws).

2. Locate code switch block. Switches are numbered 1

through 6.

3. Arrange the switches in the exact combination as

the code that you set in the receiver. It is important

that the same exact code be set in the receiver and

all transmitters. If the codes differ, the unit will not

function properly.

4. Reinstall cover. Repeat this procedure for all

transmitters.

5. Test each transmitter to ensure that the unit is

functioning properly.

6. If not, verify that all codes are set the same.

When all transmitters are functioning properly, your

WaterCop

system is on duty to help protect

your home from damage due to plumbing leaks.

WaterCop

Interface Connections

Contacts 5, 6 & 7 are used to control the valve position

from a remote location. The most common is your

home security system control panel.

This is done by wiring these contacts to a control

switch on the panel. The diagram at right shows typi-

cal installation options. This control can be a relay,

push buttons or toggle type switch. This control needs

to be a momentary switch which means that the control

switch stays made or 'on' for a short period of time (1

to 3 seconds) and then returns to a neutral position.

Contacts 2, 3 & 4 are used to signal a remote device

as to the position of the valve.

connecting a low voltage circuit with indicator lights to

these contacts. The diagram shows a typical

installation.

This is done by

DynaQuip Contols

10 Harris Ind. Pk., St. Clair, MO 63077

800-545-3636

www.watercop.com

When the valve is in the open position contacts 2 & 3

will be made completing the circuit and lighting the indi-

cator light, showing that the valve is in the normal open

position.

When the valve is in the closed position, contacts 3 &

4 will be made completing the circuit and lighting the

indicator light, showing that the valve is closed.

Emergency Procedures

In the unlikely event that the WaterCop

should shut off the main water supply and then

become inoperable due to a power outage or damage,

it is possible to manually operate the WaterCop

return water service. Unplug the WaterCop

power source. The valve may be manually opened by

removing the four screws holding the housing to the

valve, sliding the housing off the valve shaft, and

turning the valve shaft a quarter turn with a

screwdriver. This procedure should only be necessary

in emergencies.

System

from its

192119 revB