DCB IP-6600 Hızlı Başlangıç Kılavuzu - Sayfa 6

Kablosuz Yönlendirici DCB IP-6600 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. DCB IP-6600 7 sayfaları.

5. Ethernet-B Static Routes – Set a host route to the remote IP-6600's Ethernet-B interface.

For our example, this would be an entry of Target: 10.225.0.8, Netmask: 255.255.255.255,

Gateway: 10.225.0.8, Failover: No. This routing entry is unnecessary because the routers

are directly connected. However, it has been included to illustrate setting a host route, which

would be necessary if the routers were not directly connected.

6. Serial-A Operating Mode – Leave all of these settings in their default state including the

disabled Port Mode.

7. Serial-A PPP Options –From the default configuration set the local IP address to

192.168.0.1 and the remote IP address to 192.168.0.2

8. Serial-A Static Routes – Set a default route to the remote router. This would be an entry of

Target: 0.0.0.0, Netmask: 0.0.0.0, Failover: Yes. Notice that this is a failover route. Its

counterpart was set back on step 4.

The local IP6600 is configured. Don't forget to activate and save your changes.

1. Ethernet-A IP Configuration – Set the IP address and Subnet Mask for your remote

network. In our example, this would be IP:10.0.2.2, Subnet Mask: 255.255.255.0.

2. Tools/ISP-Failover - Enable failover and select the ping method. Set Ethernet-B as the

primary interface and Serial-A as the failover interface. Set both the Failover-Time and

Recovery-Time to 10 seconds. Set the Ping Target. This will be the IP address of the local

IP-6600's Ethernet-B interface. For our example, this would be 10.225.0.7. Enable the Block

Default Route field.

3. Ethernet-B IP Configuration – Set the IP address and Subnet Mask for your primary

connection. In our example, this would be IP: 10.225.0.8, Subnet Mask: 255.255.255.0.

4. Ethernet-B Static Routes – Set a default route to the local router. For our example, this

would be an entry of Target: 0.0.0.0, Netmask: 0.0.0.0, Gateway: 10.225.0.7, Failover: Yes.

Notice that this is a failover route.

5. Ethernet-B Static Routes – Set a host route to the remote IP-6600's Ethernet-B interface.

For our example, this would be an entry of Target: 10.225.0.7, Netmask: 255.255.255.255,

Gateway: 10.225.0.7, Failover: No. This routing entry is unnecessary because the routers

are directly connected. However, it has been included to illustrate setting a host route, which

would be necessary if the routers were not directly connected.

6. Serial-A Operating Mode – Leave all of these settings in their default state including the

disabled Port Mode.

7. Serial-A PPP Options – Leave all of these settings in their default state.

8. Serial-A Static Routes – Set a default route to the remote router. This would be an entry of

Target: 0.0.0.0, Netmask: 0.0.0.0, Failover: Yes. Notice that this is a failover route. Its

counterpart was set back on step 4.

The remote IP6600 is configured. Don't forget to activate and save your changes.

Remote IP-6600

Data Comm for Business, Inc.

2949 County Road 1000 E

Dewey, IL 61840

217-897-6600, FAX 217-897-1331

Outside Illinois: 800-4DCBNET

http://www.dcbnet.com