Autopage C3-RS-601 Kurulum Kılavuzu - Sayfa 12

Uzaktan Çalıştırıcı Autopage C3-RS-601 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Autopage C3-RS-601 19 sayfaları. Remote car starter
Ayrıca Autopage C3-RS-601 için: Hızlı Başlangıç Kurulum Kılavuzu (2 sayfalar)

Sayfayı Yazdır
FEATURE "III" PROGRAMMING:
Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
1. Push the Valet switch 3 times (holding in on the 3
the valet switch. You are now in the Alarm feature "A" programming mode.
2. Press and release the transmitter button corresponding to the feature you want to program.
Press
One Chirp /
Transmitter
LED one pulse
Button
Factory Default Setting
20 minutes run time
1.
0.8-second Door lock & Unlock.
2.
Five chirps= 0.8 second lock, dbl 0.8 second unlock
Six chirps= dbl 0.8 second lock, 0.8 second unlock
Door Lock before
3.
+
start
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
FEATURE "IV" PROGRAMMING:
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2. Push the Valet switch 4 times (holding in on the 4
the valet switch. You are now in the Alarm feature "A" programming mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
Press
One Chirp /
Transmitter
LED one pulse
Button
Factory Default Setting
Tachometer checking type.
1.
RPM learning
Start Timer:
2.
0.6-second
Low check level
3.
+
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
FEATURE "V" PROGRAMMING:
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2. Push the Valet switch 5 times (holding in on the 5
the valet switch. You are now in the Alarm feature "A" programming mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
Press
One Chirp /
Transmitter
LED one pulse
Button
Factory Default Setting
Second Accessory
1.
H3/9 Blue/Black
+ 50 RPM
2.
DBI ONLY
- 50 RPM
3.
+
DBI ONLY
RS-603 REV A.
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
rd
push ) until three chirps with one long chirp is heard, then release
Two Chirps /
LED two
pulse
10 minutes
run time
3.5-second
Door
Lock &
Unlock.
Door Lock before & after start *
Door Lock after
This is the preferred setting when
start
using the optional XT-11 single
button remote
th
push ) until four chirps with one long chirp is heard, then release
Two Chirps /
LED two
pulse
Voltage
checking type
0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4
chirps), 1.4-second (5 chirps), 1.6-second (6 chirps),
1.8-second (7 chirps), 2.0-second (8 chirps), 3.0-second (9
chirps), 4.0-second (10 chirps),
Hi check level
th
push ) until five chirps with one long chirp is heard, then release
Two Chirps /
LED two pulse
Second Start
H3/9 Blue/Black
No RPM learning
No RPM Learning or < 50RPM
12
Three Chirps /
Four Chirps /
LED three pulse
LED four pulse
30 minutes run
5 minutes run time
time
0.8 second lock,
0.8 second dbl
0.35 second
lock,0.8 second dbl
unlock
unlock
Without this
feature
Three Chirps /
Four Chirps / LED four
LED three pulse
pulse
Timer checking
DBI TACH **
type
DATA ONLY !!
Three Chirps /
Four Chirps / LED
LED three pulse
four pulse
7/9/2008