Autopage 355A Kurulum Kılavuzu

Güvenlik Sistemi Autopage 355A için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. Autopage 355A 3 sayfaları.

Sayfayı Yazdır

5 PIN WIRE HARNESS

1. Red / White Wire: Parking Light Relay input

2. White Wire: Parking Light Relay Output

3. Black Wire: Ground to Vehicle FRAME

4. Brown Wire: Positive output To

Siren

5. Red Wire: +12V To Constant Battery Source

This manual was written September 1, 2015

GI-S346

INSTALLATION MANUAL

8 PIN CONNECTOR WIRE HARNESS:

* Starter Kill relay optional

ALARM FEATURE "I" PROGRAMMING:

Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.

Push the Valet switch 3 times and hold in on the 3rd push. When a long chirp is heard, release the

valet switch. You are now in the Alarm feature 'I' programming mode.

Press the transmitter button corresponding to the feature you want to program.

a. The factory default settings is always [1] LED flash, [1] chirp.

Depress the transmitter button again to change the feature. Simply keep pressing the transmitter

button again until the module advances to your desired setting.

One Chirp /

Press

LED one pulse

Transmitter

Factory Default

Button

Setting

Active arming

Automatic Rearm off

Instant Door Ajar

error chirp

Siren Confirmation

chirp on only

White wire=

15A Fuse

Dome Light Output

Lock/Arm &

Unlock/Disarm

Confirmation Chirps

ALARM with

Keyless Entry

Car Jacking

feature Off

355A

Three Chirps

Four Chirps /

Two Chirps /

LED four

LED two pulses

LED three

pulses

Passive

Passive arming

arming with

without passive

passive door

door locking

locking.

Automatic Rearm

45 seconds delay

Door Ajar error

chirp.

Horn

All

All Confirmation

Confirmation

chirps On

chirp on only

chirps off

White =

White wire=

Channel

channel

Momentary

Latched

Lock/Arm

Confirmation

Chirp Only

Keyless Entry

ONLY

Car Jacking

feature On

355A

Transmitter Programming

Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter

memory is exceeded, the security system will start deleting transmitters from memory in

chronological order.

1. Turn the Ignition 'switch 'OFF/ON' 3 TIMES and stay in ON position.

"Within 15 seconds".

2. Push the Valet switch 2 times and hold it on the 2

release the valet switch. You are now in the Transmitter programming mode.

3. Press and hold any button of the transmitter until the siren responds with a confirming chirp,

indicating the signal has been stored into memory.

4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for

each transmitter.

Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light

flashes will confirm exit.

ALARM FEATURE "B" PROGRAMMING:

Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.

Push the Valet switch 5 times and hold in on the 5

push. When a long chirp is heard, release the

valet switch. You are now in the Alarm feature 'B' programming mode.

Press the transmitter button corresponding to the feature you want to program.

One Chirp / LED

Press

one pulse

Transmitter

Two Chirps / LED

Three Chirps / LED

two pulses

three pulses

Factory Default

Button

Setting

Pathway

Parking light turns

illumination feature

"on" for 30- second

"off"

upon an unlock

upon an unlock signal

signal

& 10-second upon a

lock signal.

Ignition controlled

door locks &

door locks only

unlocks

0.8-second Door

3.5-second Door

Double pulse unlock

lock pulses.

lock pulse.

Channel Pulsed

Channel

Momentary

Button =

Button = 4

Channel Aux.

Silent Arm/Disarm

Gray Wire = Trunk

Gray Wire = Two

(Channel 3) Output

Step Door Unlock

Output

Horn chirp Duration

Standard

50 mS

30 mS

Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.

SHOCK SENSOR ADJUSTMENT

1. Turn the Ignition switch 'ON/OFF' 3 TIMES and stay in OFF position.

2. Push the Valet switch 7 times holding in on the 7th push. Three chirps with a long chirp will be heard. Release the valet

switch. You are now in the Alarm feature 'Shock Sensor' programming mode.

3. Press and hold

button for 2 seconds. One long siren chirp will indicate the unit is ready to accept adjustments of the

shock sensor.

4. Press

button on the transmitter once. This will decrease sensitivity level by one. Each time the button is pushed and a

decrease is made the siren/horn chirp will respond with [1] chirp. Two chirps indicate the minimum sensitivity. Warn away &

full trigger will be deleted when minimum sensitivity is selected

5. Press

button on the transmitter once. This will increase sensitivity level by one. Each time an increase is made the

siren/horn chirp will respond with [1] chirp. Two chirps indicate the maximum sensitivity.

6. Hit the bumper or strong metal part of the vehicle to test the threshold level of the sensor.

a). Activate the warn-away (first stage the shock sensor), the siren will emit a short chirp.

b). Activate the full alarm (second stage the shock sensor), the siren will emit a long chirp.

7. When you are satisfied with the setting, press the

button to lock in the adjustment. One long siren chirp will indicate the

unit has locked in the adjustment.

Note: If 30 seconds of inactivity expires or you turn ON the ignition during of above steps, the unit will exit the program mode

and return to the disarmed mode. Three long chirps will confirm exit.

Varad International, Inc.

5349 Zambrano Street,

Commerce,CA 90040

www.varad.com

push until a long chirp is heard then

Four Chirps /

LED four

pulses

Without ignition

Ignition controlled

controlled door

door unlocks only

locks & unlocks

Comfort feature

Horn chirp

duration

10 mS