Highlander iP-1 Manuel - Sayfa 2

Müzik Enstrümanları İçin Aksesuarlar Highlander iP-1 için çevrimiçi göz atın veya pdf Manuel indirin. Highlander iP-1 4 sayfaları. Integrated pickup and preamplifier for acoustic guitar and bass integrated pickup and preamplifier for acoustic guitar and bass

Sayfayı Yazdır

i P- 1 I N S TA L L AT I O N

iP-1 INSTALL ATION

O R A G O O D W O O D W O R K E R W I T H E X P ER I E N C E W O R K I N G O N ACO U S T I C S T R I N G E D I N S T RU M E N TS .

O R A G O O D W O O D W O R K E R W I T H E X P E R I E N C E W O R K I N G O N ACO U S T I C S T R I N G E D I N S T R U M E N TS .

About the Output Jack

The iP-1 is turned on when a guitar cord

is plugged in and turned off when it is

unplugged, saving the battery.

The information and graphics contained in this document are the property of Highlander Musical Audio Products. Copying of any kind is prohibited, except for personal use only.

T H I S I N S TA L L AT I O N S H O U L D O N LY B E U N D E R TA K EN B Y A N E X P E R I E NC E D LU T H I E R

T H I S I N S TA L L AT I O N S H O U L D O N LY B E U N D E R TA K E N B Y A N E X P E R I E N C E D LU T H I E R

Using the wrong techniques or tools could result in permanent damage to your guitar.

Highlander is not responsible for any damage resulting from the installation of this pickup system.

Parts Included:

Qty. Description

Pre-wired iP-1 Pickup/Preamp Assembly

Battery Holder Clips for 9 Volt Battery

Pieces of Self Adhesive Velcro® for cable strain relief

Tools Required:

HAND DRILL or ELECTRIC DRILL (cordless preferred)

MILLING MACHINE or ROUTER AND SADDLE SLOTTING JIG

Used for routing the groove

3)* 17/32" (13.5mm) DRILL BIT, RELIEVED ON RAKE EDGES

Used for drilling guitar end block for the strap jack

4)* 9/16"-12 TPI NC TAP & MACHINIST'S TAP HANDLE

Used for threading end block to accept the strap jack

5)* 1/16" (1.6mm) DIAMETER BALL ENDED END MILL

Used for routing the groove in the bottom of the saddle slot

3/32" (2.5mm) TWIST DRILL BIT

Used for drilling both holes in the saddle slot for the pickup

MILLING MACHINE or DISC / BELT SANDER or

MACHINIST'S VISE AND FILE. STRAIGHT EDGE

Used for reducing saddle height to

compensate for the pickup thickness

* The following installation tools are available from Highlander:

17/32" drill bit

9/16"-12TPI tap bit

1/16" router bit

These tools are available individually or as the 'iP-installation kit'

For optimum pickup per f r formance and ease of installation, please take a

For optimum pickup pe

ormance and ease of installation, please take a

moment to read through this Installation Guide before beginning. Thank You.

This innovative screw thread is designed

to stay in place regardless of variations in

the end block as it expands and contracts

due to humidity and temperature changes.

By eliminating the typical machine thread

and nut, our preamp will never come loose

and require the awkward task of tightening

a nut at the end pin block inside the guitar.

The elegant strap button holds the strap

securely and will never untwist or loosen.

Highlander Musical Audio Products 1991-2009