Gallien-Krueger Backline 110 Kullanıcı El Kitabı - Sayfa 4
Amplifikatör Gallien-Krueger Backline 110 için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Gallien-Krueger Backline 110 12 sayfaları. Backline series
Ayrıca Gallien-Krueger Backline 110 için: Kullanıcı El Kitabı (16 sayfalar)
Sayfayı Yazdır
Safety Information
Please read all enclosed safety precautions, before
connecting or operating this product.
Verify Line Voltage and Amperage Before Use:
Your new MicroBass Series amplifier has been fac-
tory configured for use with:
120 Volt/60Hz 15 A circuit for USA/Canada.
230 Volt/50Hz 10 A circuit for UK/Australia.
240 Volt/50Hz 10 A circuit for Europe.
100 Volt/50Hz 15 A circuit for Japan.
220 Volt/50Hz 10 A circuit for Korea.
Connecting the amplifier to a line with specifications
other than indicated above can create a safety or fire
hazard and may damage the amplifier. If you have
any questions about the voltage requirements for your
specific model, or about the line voltage in your area,
contact your dealer before plugging the unit into a
wall outlet.
Verify AC Circuit Capacity Before Use:
The high power output of your amplifier may require
heavy current draw under full-load conditions. To
insure proper performance and avoid potential safety
hazards, we recommend connection to line circuits
with amperage specified "as above". Connecting
multiple amplifiers to the same circuit, or connect-
ing the amplifier to the same circuit used by other
heavy-power devices, such as high-wattage lights,
may cause circuit breakers to trip. It is always a good
idea to avoid using any audio equipment on the same
AC circuit as equipment with motors, such as air con-
ditioners or refrigerators. This will lessen the possi-
bility of power variation and electrical start-up noise
affecting your sound.
AC Power Cord:
To avoid safety hazards, use only the power cord
supplied with your unit. If a replacement cord is
needed, make certain that to use a standard IEC com-
pliant cord. Damaged power cords should be replaced
immediately.
B B B B B A C K
A C K
A C KLINE 110 & 112
A C K
LINE 110 & 112
LINE 110 & 112
LINE 110 & 112
A C K
LINE 110 & 112
Connecting to AC Power:
When setting up, make certain that the AC plug is
easily accessible. If mounting in a rack, ensure that
the AC mains can be easily disconnected by a plug
or by an all-pole disconnect switch on or near the
rack.
Disconnect When Not In Use:
If you do not intend to use the amplifier for a con-
siderable length of time, disconnect the plug from
the AC outlet. Just switching the unit off does not
mean that it is fully disconnected from the AC Mains.
To isolate the unit from the AC mains, you must
disconnect the power cord from the unit and the AC
outlet. When disconnecting the power cord always
pull from the plug, never pull from the cord.
Do Not Open the Amplifier Enclosure:
There are no user-serviceable components inside this
product. Opening the amplifier enclosure may present
a shock hazard, and modification to the product will
void your warranty. If liquid enters the unit, or any
metal object such as a paper clip, wire, or staple ac-
cidentally falls inside the enclosure, disconnect the
unit from the AC power source immediately and con-
sult an authorized service station.
Unpacking:
The carton and packing materials used in shipping
your new amplifier were specifically designed to cush-
ion it from the shocks and vibration that occur dur-
ing transport. We suggest that you save the carton
and packing materials for use in shipping, in the event
you move, or the amplifier needs repair.
4