Gallo Tech GTS-3RS Kullanım ve Kurulum Kılavuzu - Sayfa 15

Araba Alarmı Gallo Tech GTS-3RS için çevrimiçi göz atın veya pdf Kullanım ve Kurulum Kılavuzu indirin. Gallo Tech GTS-3RS 16 sayfaları. Keyless rfid push button start & security system

Sayfayı Yazdır

1. Installation Instructions

Installing Connector C4:

The HF antenna is used for the high frequency receiver that operates the remote access functions such as remote

door locking, and car locating. For maximum range the antenna should be mounted above the dash board level. The

antenna can be mounted under the dash however the detection range may be reduced. Caution should be taken as

the antenna whip is metal and the installer should insure that the whip will not interfere / short out any under-dash

wiring. Connect the 3 Pin (Red) connector to the Control Module as shown in Figure 1.

Installing Connector C5:

The "Start Stop Engine" button can be surface mounted in a convenient location on the dash. The Black bezel

around the switch is removable to customize the installation. The high strength double stick adhesive disk is to be

used on the back side of the switch for mounting purposes. Once attached, it will be difficult to remove. Make certain

that the back of the button and the mounting surface is thoroughly cleaned with isopropyl alcohol to remove any

dirt, grease or vinyl dressing materials. DO NOT use acetone, MEK, lacquer thinner or any other harsh

chemicals as they will destroy paint, vinyl and plastic. The adhesive will not come loose or degrade as long as

the surface has been cleaned thoroughly. Attach the adhesive disk to the back of the button first.

If you choose to mount the button on the dash with the wire hidden behind the button then drill a 1/2" dia. hole in a

location where the small wire and connector can be fed through the dash. It is recommended that the hole be drilled

just below the centerline of the final switch location, approximately where the wires exit the back of the switch. Rout

the "Start Stop Engine" button wire to the module. Connect the C5 (White) 6 pin connector to the module as shown

in Figure 1.

Installing Connector C6:

Shock Sensor (included) – The adjustable 2 stage shock sensor or an aftermarket motion sensor can be

connected to either Connector C6 or C7. The shock sensor should be mounted on a rigid member of the vehicle.

Typically it is best attached to the steering column. The shock sensor should never be mounted on the outside of the

vehicle where it is not protected from exposure to moisture. Connect the 4 Pin (White) connector to both the shock

sensor and the Control Module as shown in Figure 1.

Aftermarket Motion sensor (not included) – A 4 wire motion sensor must be used. Chances are the connectors

may not be the same as the GTS-3RS. If connecting an aftermarket sensor to GTS-3RS go to our Support web page

(www.gallotech.com/support) for the proper wiring configuration.

Installing Connector C7:

See Connector C6 above. Installation is the same for both connectors.

Installing Connector C8:

The Valet Switch should be mounted under the dash or in the glove box so that it can be accessed from time to time

to change or modify the programmable functions of GTS-3RS. Connect the 2 pin (Black) connector to the Control

Module as shown in Figure 1.

1.8 FINAL INSTALLATION

1. Recheck all electrical connections to be certain they are connected in the proper locations and check

that all connections are wrapped with a good quality electrical tape or shrink tubing. Connect all 8

module connectors to the Control Module. All connectors are indexed so that they can only be installed

in one direction. The Control Module should be secured under the dash using cable ties or equivalent. If

the vehicle is equipped with a locking steering column, it must be permanently disabled before

3 Pin (RED) Wire Harness - HF Antenna

6 Pin (White) "Start/Stop Engine" button switch

4 PIN (White) Wire Harness

2 Pin (Black) Valet Switch wire harness

Shock sensor (included) or motion device.

- 15 -

061515V54RS