Coral Box RN1 Kullanıcı Kılavuzu - Sayfa 2
Su Pompası Coral Box RN1 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Coral Box RN1 3 sayfaları. Reverse nano pump
Sayfayı Yazdır2.Introduction of each mode
F1:Stream Mode
One or more pumps
can operate at the
same time, in
constant flow.
F2:Pulse Mode
One or more pumps
can operate at the
same time,in pulse
flow.
Pulse the wave by
time / flow frequency.
Nature Mode(LPS)
Reef Mode(SPS)
F3:Asynchronous
Wave Mode
Shift flow in cycles,
Pump A run, Pump B
stop;Pump B run,
Pump A stop
Need have 2 Pump
with WIFI master and
slave to run.
F1,F2,F3,F4,F5,F7 can press "Frequency/Reverse" button to adjust the
Frequency,Press "Up/Down"arrows to adjust the Flow.
3.How to Set the Timer?
First you need to press
"MODE/NIGHT" button to select F6 Timer mode.
Enter in the programming mode by pressing
Move the cursor in the position to be set by using
F4:Nature Mode
The power level
changes between
30%~100%
making a more
natural flow pattern.
F5:Reef Mode
Power of flow is
changing in a
random mode in
volume and time.
This is the best
mode for corals.
F7: Reverse Mode
Clockwise
pump.The pump
uses the opposite
direction of the
water flow to
improve cleaning of
your tank.
F6:Timer Mode
Six different operative modes can be set in
this mode. For example, the first set of 9 a.m
to 10 a.m stream mode, the second set of
10 a.m to 1 p.m pulse mode.
F0: Stop Mode
It only works in the Timer Mode(F6). This
mode stops the Pump running in the
programmed time slot.
"Timer switch" button.
Left/Right arrows.
Adjust Current Time/Schedule/Timer/mode by using
4.Sequence Modes Setting:
Press "time switch" button to enter in the programming mode. Using left/right arrows, move
the cursor on the digit of the Schedule (T), and change it from 1 to 6 using up/down
arrows. Example if first time slot is to be programmed, digit shown in the display are: T1
Using left/right arrows, move the cursor on the Start Time digits. Move up/down arrows up
to achieve the desired figure. Example if start time is set to 09:00 than digit in the display
are: 09S
Using left/right arrows, move the cursor on the End Time digits. Move up/down arrows up to
achieve the desired figure. Example if end time is set to 11:00 than digit in the display are:
11E
Using left/right arrows, move the cursor on the Function digit. Move up/down arrows up to
achieve the desired function mode from 0 to 5. Example if mode is set to 1, then digit shown
in the display are: F1
Here is possible to set the Stop Mode (F0).
As a reference here below an example of daily program in multifunctional mode.
Display
Schedule
T1
T2
T3
T4
T5
T6
*Attention: To provides best motor impeller performance F7 reverse mode cannot
operation to timer to avoid Long time running.
Ⅵ.Warnings
Do not operate the pump outside water to ensure the performance.
Select a dry place to locate the controller to prevent water could be splashed on it.
Pay attention during magnets assembly. It is recommended to locate the magnetic pad
close to the outside wall of fish tank to prevent breaking the fish tank and then shift it in
Up/Down arrows.
Timer ( Start ~ End )
Function
09:00 Start ~ 11:00 End
11:00 Start ~ 13:00 End
13:00 Start ~ 15:00 End
15:00 Start ~ 18:00 End
18:00 Start ~ 22:00 End
22:00 Start ~ 09:00 End
F1
F2
F3
F4
F5
F4