Airespace AS 1500 Hızlı Kurulum Kılavuzu - Sayfa 4

Kablosuz Erişim Noktası Airespace AS 1500 için çevrimiçi göz atın veya pdf Hızlı Kurulum Kılavuzu indirin. Airespace AS 1500 15 sayfaları. Intelligent rf ap

Sayfayı Yazdır

minutes. If the AP remains in this mode for more than five minutes, the AP is unable to

find the Master Airespace Switch or Appliance. Check the connection between the AP

and the Airespace Switch or Appliance and make sure the Airespace AP and the

Airespace Switch or Appliance are on the same subnet.

If the Power light does not come on, check the power (it can be powered either with

Power over Ethernet or a from an orderable AP External Power Supply.

Make sure that a DHCP server is configured in the Airespace Switch or Appliance for

both the Management Interface and AP-Manager Interface using the CLI, Web Browser,

or ACS interface, and that the DHCP server is operating correctly.

Once the AP finds the Airespace Switch or Appliance, it attempts to download the new

Airespace Operating System code if the AP code version differs from the Airespace

Switch or Appliance code version. While this is happening, the LEDs on the top of the

AP blink on and off together.

Once the Airespace Operating System code download is successful, the AP reboots. The GREEN

LED turns on and the two AMBER/AMBER LEDs indicate the states of the 802.11a and 802.11b/

g networks. If a AMBER/AMBER LED remains off.

Note that the Red LED can light for a short period (10-20 seconds) when the AP

reboots. If the RED LED comes on AND STAYS ON for more than a minute, disconnect

the AP and call Airespace Global Services & Support.

Use the CLI command show ap summary. If the new AP appears on the list, it has been

configured successfully.

From the CLI, Web Browser or ACS interface, configure the AP with its Primary,

Secondary and Tertiary Airespace Switch or Appliance names as described in the

Airespace Product

If you will be using the AP in a mobility or a WPS group, set the mobility or WPS group

name using the CLI, Web Browser or ACS interface.

If required, use the CLI, Web Browser or ACS interface to customize the AP-specific

802.11a, 802.11b and 802.11g network settings. Once again, the two AMBER/AMBER

LEDs indicate the states of the 802.11a and 802.11b/g networks. If any part of the

network is disabled, the corresponding AMBER/AMBER LED remains off.

If everything works correctly (the GREEN LED is on and the RED LED is off), disconnect the

Airespace AP and take it to its final destination and install it as described in this document. If

your Airespace AP fails this visual test, refer to RMA Procedures in the

to return your Airespace APs.

When you have installed and powered up the Airespace AP in its final destination, verify that

the LEDs are in the same state they were in at the end of Step 4.

If no LEDs are on, the AP is most likely not receiving power.

If the LEDs blink sequentially back and forth for more than five minutes, the Airespace

AP is unable to find its Primary, Secondary or Tertiary Airespace Switch or Appliance.

Check the connection between the Airespace AP and the Airespace Switch or Appliance,

and make sure the AP and the Airespace Switch or Appliance are either on the same

subnet or that the AP has a route back to its Primary, Secondary and Tertiary Airespace

Switches and Appliances.

If the Airespace AP is not on the same subnet as the Airespace Switch or Appliance,

make sure there is a DHCP server on the same subnet as the Airespace AP. Also, make

sure that the route between the Airespace AP and the Airespace Switch or Appliance

can process IP fragmented packets.

12/29/04

90-100tbd-000 Rev 1 (Preliminary 3)

Guide.

Step 2: Configuring the Airespace AP Before Installation

Airespace Product Guide