Deaf Bonce Machete series Kullanıcı Kılavuzu - Sayfa 3

Hoparlör Sistemi Deaf Bonce Machete series için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Deaf Bonce Machete series 16 sayfaları. Hf speakers
Ayrıca Deaf Bonce Machete series için: Kullanıcı El Kitabı (16 sayfalar), Kullanıcı El Kitabı (12 sayfalar), Kullanıcı El Kitabı (8 sayfalar), Kullanıcı El Kitabı (20 sayfalar), Kullanıcı El Kitabı (16 sayfalar), Kullanıcı Kılavuzu (16 sayfalar), Kullanıcı El Kitabı (20 sayfalar), Kullanıcı El Kitabı (16 sayfalar), Kullanıcı El Kitabı (16 sayfalar), Kullanıcı El Kitabı (20 sayfalar), Kullanıcı El Kitabı (20 sayfalar), Kullanıcı El Kitabı (12 sayfalar), Kullanıcı El Kitabı (16 sayfalar), Kullanıcı El Kitabı (16 sayfalar), Kullanıcı El Kitabı (16 sayfalar), Kullanıcı El Kitabı (16 sayfalar), Kullanıcı El Kitabı (12 sayfalar), Kullanıcı El Kitabı (16 sayfalar), Kullanıcı El Kitabı (16 sayfalar)

1 . I N T R O D U C T I O N

Thank you for purchasing this Deaf Bonce product of Machete series! Our company is committed to the creation of extremely

high-proﬁle systems with no loss of quality.

To ensure proper use, please carefully read through this manual before using this product. It is especially important that you

read and observe caution's in this manual. Please keep the manual in a safe and accessible place for future reference.

2 . S A F E T Y I N S T R U C T I O N S

1. Fasten the audio system properly when installing it in the vehicle. If the component is disconnected during driving, it may

cause serious damage to the passengers of the car or another vehicle.

2. Before installing the components, if possible store the product in the original package to avoid accidental demage to the

product.

3. Be careful when installing and dismantling the speaker systems! Do not let the speaker drop to avoid damage of its moving

parts.

4. When working with tools follow safety rules.

5. Before the installation switch oﬀ the head unit and all other audio devices to avoid their damage.

6. Make sure that the location of the audio system does not hinder the proper operation of mechanical and electrical devices

of the vehicle.

7. Do not install components in places exposed to water, excessive humidity, high or low temperature, dust or dirt.

ATTENTION!!! The product may be operated at +5 to +40 °C. In case of moisture condensation, allow the product to dry.

8. When drilling or cutting out holes in the body of the car, make sure that there are no cables or any other important

construction elements under a selected area or inside it.

9. When stretching the speaker cables make sure that they are not in contact with sharp edges or moving mechanical devices.

Make sure that they are ﬁrmly ﬁxed and protected over the entire length.

10. The diameter of the speaker cables must be selected in accordance with the length and applied power.

11. Never stretch the cables outside of the car and near the moving parts of the car. This can lead to destruction of the

insulating layer, short circuit and ﬁre.

12. To protect the cables use rubber gaskets if the wire passes through a hole in the plate, or other similar materials if it lies

close to the parts exposed to heat.

13. Possible commutation versions are presented on the following pages. Using the data from the diagram below, check the

minimum resistance and the connection speciﬁed by the manufacturer of your ampliﬁer. Do not expose the ampliﬁer to loads

below the predetermined value.

CAUTION!!! High sound pressure can damage your health!

3 . W I R I N G D I A G R A M S

Use these diagrams to calculate the resistance of diﬀerent connection types.

S E R I A L C O N N E C T I O N O F T H E S P E A K E R S

Please use the common sense when controlling volume!

Voice coil

4 Ohm

Total impedance

8 Ohm