HIKOKI WH 18DFX Taşıma Talimatları Kılavuzu - Sayfa 5

Döner Çekiç HIKOKI WH 18DFX için çevrimiçi göz atın veya pdf Taşıma Talimatları Kılavuzu indirin. HIKOKI WH 18DFX 17 sayfaları.

Sayfayı Yazdır

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by the

manufacturer.

A charger that is suitable for one type of battery pack

may create a risk of ﬁ re when used with another

battery pack.

b) Use

power

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or

burns.

e) Do not use a battery pack or tool that is damaged

or modiﬁ ed.

Damaged

unpredictable behaviour resulting in ﬁ re, explosion

or risk of injury.

f) Do not expose a battery pack or tool to ﬁ re or

excessive temperature.

Exposure to ﬁ re or temperature above 130°C may

cause explosion.

g) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range speciﬁ ed in the instructions.

Charging improperly or at temperatures outside

the speciﬁ ed range may damage the battery and

increase the risk of ﬁ re.

6) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

b) Never service damaged battery packs.

Service of battery packs should only be performed

by the manufacturer or authorized service providers.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of

children and inﬁ rm persons.

CORDLESS IMPACT DRIVER SAFETY

WARNINGS

Hold the power tool by insulated gripping surfaces,

when performing an operation where the fastener may

contact hidden wiring. Fasteners contacting a "live" wire

may make exposed metal parts of the power tool "live" and

could give the operator an electric shock.

tools

only

with

speciﬁ cally

modiﬁ ed

batteries

may

ADDITIONAL SAFETY WARNINGS

1. This is a portable tool for tightening and loosening

screws, bolts and nuts. Use it only for these operation.

2. Make sure to securely hold the tool during operation.

Failure to do so can result in accidents or injuries.

(Fig. 2)

3. Preparing and checking the work environment. Make

sure that the work site meets all the conditions laid forth

in the precautions.

4. Check the actual tightening torque with a toruqe wrench.

5. Stop the tool before switching the direction of rotation.

Always release the switch and wait for tool to stop before

switching the direction of rotation.

6. Never touch the turning part. Do not allow the turning

part section to get near your hands or any other part of

your body. You could be cut or caught in the turning part.

Also, be careful not to touch the turning part after using

continuously it for a long time. It gets quite hot and could

burn you.

7. Please use the designated attachments which are

listed in the operations manual and HiKOKI's catalog.

Accidents or injuries could result from not doing so.

8. Make sure to ﬁ rmly install the attachments in the anvil. If

the attachments is not ﬁ rmly installed it might come out

and cause injuries.

After installing the driver bit, pull lightly out the bit to

make sure that it does not come loose during use. If the

guide sleeve does not return to its original position, then

the bit is not installed properly.

9. Resting the unit after continuous work.

exhibit

10. Cautions on use of the speed control switch

This switch has a built-in, electronic circuit which

steplessly varies the rotation speed. Consequently,

when the switch trigger is pulled only slightly (low speed

rotation) and the motor is stopped while continuously

driving in screws, the components of the electronic

circuit parts may overheat and be damaged.

11. Do not touch the metal parts, as it gets very hot during

continuous work.

12. The use of the battery in a cold condition (below 0 degree

Centigrade) can sometimes result in the weakened

tightening torque and reduced amount of work. This,

however, is a temporary phenomenon, and returns to

normal when the battery warms up.

13. Do not look directly into the light. Such actions could

result in eye injury.

Wipe oﬀ any dirt or grime attached to the lens of the LED

light with a soft cloth, being careful not to scratch the

lens.

Scratches on the lens of the LED light can result in

decreased brightness.

14. Install securely the hook. Unless the hook is securely

installed, it may cause an injury while using.

When electing to carry the tool hooked to your hip belt,

make sure to detach the tool bit. Failure to do so may

result in unexpected injury.

15. Always use the tool and the battery at temperatures

between -5oC and 40oC

16. Always charge the battery at an ambient temperature of

0°C–40°C.

17. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

18. Never disassemble the rechargeable battery and

charger.

19. Never

short-circuit

Shortcircuiting the battery will cause a great electric

current and overheat. It results in burn or damage to the

battery.

20. Do not dispose of the battery in ﬁ re. If the battery is burnt,

it may explode.

the

rechargeable

battery.