Green GPM-303 Hızlı Kılavuz
Kasa Sayacı Green GPM-303 için çevrimiçi göz atın veya pdf Hızlı Kılavuz indirin. Green GPM-303 2 sayfaları. Programmable counter
Sayfayı Yazdır
DIMENSIONS
I / P PULSE
RELAY
48
SET
GREEN
GPM - 303
PROGRAMMABLE COUNTER
96
PANEL CUTOUT DIMENSION
45
SPECIFICATIONS
Range
Display
Reset : Auto / Manual
Input
Pulse frequency
Special feature
Indications
Set points
Output
Relay contact rating
(Resistive load)
Mechanical life of relay
Electrical life of relay
User programming
Count direction
Power consumption
Supply voltage
Operating voltage range
Weight
Dimension ( L x W x D )
Ambient humidity
Ambient temperature
Storage temperature
In the pack
75
10
All dimensions are in mm
90
999 999 Counts
Six digits, 0.4 Inch seven segment LED
Auto reset Time 000.1 Sec to 999.9 Sec
NPN (or) PNP Proximity unit (Selectable)
Low : Less than 30 Hz & High : More than 30 Hz
Memory Retension
Input Pulse and Relay ON
Two (Count and auto reset time)
One relay, 1 c/o
10 A @ 230 VAC
/ 30 VDC
10 million operation
100000 operation
3 Keys & Display
Up
4.8 VA
230 VAC
+ / -10% from the rated voltage
170 grams
96 x 48 x 75
35 to 85 % RH
-10 to 55 c
-25 to 65 c
counter, side clamp and instruction manual
GPM - 303
PROGRAMMABLE COUNTER
INTRODUCTION
Thank you very much for purchasing this GREEN product
GPM-303. Please read the instruction manual carefully for
the full usage of this product
The
COUNTER
has passed various quality tests before despatch.
Please check however, at the time of arrival, its model code
and its appearance and ensure that all the contents are provided
and there are no faults, damage etc, to the timer. Please also
ensure that the model code ,which is labeled on the timer,
is identical to the one you ordered.
F
NOTE:
1. Our company shall not be liable for any damages, as described
below, caused to both any users and third parties
a) Damages caused by the result of operation of the product.
b) Damages caused by any defects in the product which are
unpredictable for us.
2. The content in this manual are subject to change without any
notice. If you have any suggestion on the matter,
Please do not hesitate to contact us.
WIRING DIAGRAM
O / P
1
2
3
SENSOR
NC
C
NO
9
10
11
MANUFACTURER
GREEN MICROELECTRONICS INDIA PVT. LTD.
green@green
electronics
.in
PRECAUTION FOR SAFE USE
(1) Use and store the Timer within the specified
ambient temperature and humidity ranges.
(2) Do not use the product in location subject to vibrations
or shocks. Using the product in such location over a long
period may result in damage due to stress.
(3) Do not use the product in locations subject to dust,
corrosive gases, or direct sunlight
(4) Separate the input signal devices, input signal cables
and the product from the source of noise or high - tension
cables producing noise
(5) The supplied power voltage and load must be within the
rated and specified ranges.
(6) Do not use where the water or oil splatter on the Timer
(7) Install a switch or circuit breaker that allows the operator
to immediately turn off the power
PROXIMITY
NPN / PNP
4
5
6
7
8
MANUAL
RESET
-
+
E
N
P
12
13
14
15
16
24 VDC
100 - 240 VAC, 50HZ
OUTPUT
SUPPLY
www.greenelectronics.in
0422-2590288
V1.2