KitchenAid JIC4430XS Kurulum Kılavuzu - Sayfa 4

Setüstü Ocak KitchenAid JIC4430XS için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. KitchenAid JIC4430XS 16 sayfaları. 30" (76.2 cm) and 36" (91.4 cm) electric induction cooktop

Sayfayı Yazdır

Electrical Requirements

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper wire.

Electrically ground cooktop.

Failure to follow these instructions can result in death,

fire, or electrical shock.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path and wire gauge are in accordance with local

codes.

Check with a qualified electrical installer if you are not sure the

cooktop is properly grounded.

It is not recommended to have a fuse in the neutral or ground

circuit.

Make sure that the electrical connection and wire size are

adequate and in conformance with the National Electrical Code,

ANSI/NFPA 70-latest edition or CSA Standards C22.1-94,

Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest

edition, and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Before You Make the Electrical Connection:

To properly install your cooktop, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

A 4-wire or 3-wire, single phase, 240 volt, 60 Hz., AC only

electrical supply is required on a separate, 50-amp circuit

(36" [91.4 cm] models) or 40-amp circuit (30" [76.2 cm]

models), fused on both sides of the line.

The cooktop should be connected directly to the junction box

through flexible, armored or nonmetallic sheathed, copper

cable. The flexible, armored cable extending from the fuse

box or circuit breaker box should be connected directly to the

junction box.

Locate the junction box to allow as much slack as possible

between the junction box and the cooktop so that the

cooktop can be moved if servicing becomes necessary in the

future.

Do not cut the conduit. The length of conduit provided is for

serviceability of the cooktop.

A UL listed or CSA approved conduit connector must be

provided at each end of the power supply cable (at the

cooktop and at the junction box). A listed conduit connector

is already provided at the cooktop.

If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

INSTALLATION INSTRUCTIONS

Prepare Location

1. Decide on the final location for the cooktop.

NOTE: Countertop must be 1

2. If necessary, make cutout in countertop before installing

cooktop. See "Location Requirements" section for more

information.

3. Clean cutout of any remaining dust and debris.

Install Brackets

NOTE: Cooktop Bracket Adhesive Kit Part Number W10310006

is required for installing the cooktop into a marble countertop.

See the "Assistance or Service" section of the Use and Care

Guide for information on ordering.

To Install Brackets into Marble Countertop:

1. Clean the brackets and cooktop cutout of any dust and

debris.

2. Measure the center line of the vertical sides of the cooktop

cutout.

" (3.0 cm) to 2" (5.1 cm) thick.

Center line