JAMAR Technologies TRAX Apollyon Hızlı Başlangıç - Sayfa 2

Ölçüm Cihazları JAMAR Technologies TRAX Apollyon için çevrimiçi göz atın veya pdf Hızlı Başlangıç indirin. JAMAR Technologies TRAX Apollyon 4 sayfaları.

Sayfayı Yazdır

Step 5 – Beginning a Count: Setting up the TRAX Apollyon

Now that we have the tubes on the road, we need to begin a study on the Apollyon. To do this, lift the Apollyon's lid and

turn it on by pressing the Power (Tab) key. Next, follow the steps below by using the DO and TAB keys.

COUNT

USB UTILS :0

Bat:3.6v

Count:00

7104K :0

15:21:58

11/04/11 :0

1: Select Count and press DO.

YES

Enter Site Code

Press DO to select

4: Select if you want to use a Site Code

or not, then press DO.

Step 6 – Checking that the TRAX Apollyon is collecting data

Now that the Apollyon is recording, we can make sure it is actually recording vehicles by watching the screen. When a ve-

hicle drives over the tubes the air pulse is registered and is displayed in the form of asterisks as shown in the image below.

L06 BASIC-DATA

A: ***********

Good

B: ***********

CNT: 01 MEM: 100% 3.8V

L06 BASIC-DATA

A: ***

B: ***********

CNT: 01 MEM: 100% 3.8V

Step 7 – Downloading Data from the TRAX Apollyon

Once you have collected all the data you want with your Apollyon, that data can be downloaded either directly to a com-

puter using a USB cable, or to a USB Memory stick. The following two sections describe both of these procedures.

Note: You cannot download a count that is still recording. You must end the count in order to download it. When you want

to end a count, simply turn the Apollyon off by pressing the POWER key and holding it down for 5-6 seconds. This shuts

the Apollyon down and stores the count file in memory. Turn the Apollyon back on to download your data.

Downloading to USB Memory Stick

Insert a USB Memory Stick into the USB Memory Port on the Apollyon. Then,

on the Main Menu, select USB then select Download. The Apollyon will begin

sending the data to the memory stick.

COUNT

USB UTILS :0

Bat:3.6v

Count:01

15:21:58

BASIC

Press DO to select

2: Select count type and press DO. We

generally recommend BASIC data.

EXIT

START

5: We are now set to begin the count.

Select Start, press DO and the Apollyon

will begin recording vehicles.

Each time a car drives over the L6 layout, both tubes get struck twice, once by the

first axle and once by the second axle. So, each time a car passes, you should see

two asterisks appear on each channel shown on the screen. One thing to watch for

when you begin your count is if one channel starts pulling ahead of the other.

If this happens it means that either one tube is missing hits, or the other is getting

too many pulses. In this case, you need to determine which tube is acting up,

and fix any issues. Common fixes include fastening a tube down more with tape,

Bad

repositioning a tube, or replacing a tube if it has holes in it.

If everything looks good with the tubes, close the lid of the Apollyon and lock it.

DOWNLOAD

7104K :0

Write ALL counts to

11/04/11 :0

the USB Flash Drive

VOLUME ONLY

TUBES

EXIT

Basic Data

STAT

EXIT

Press DO to Start

v3.66

L1 L2 L3 L4 L5 L6 L7

L8 L9 10 11 12 13 14

L1: Two Channel Vol.

A,B

3: Select the layout you installed in the

field and press DO.

L06 BASIC-DATA

CNT: 01 MEM:97% 3.6v

6: Here we see the screen as it appears

while the Apollyon is in count mode.

EXIT