Ganz GH Series Kurulum ve Kullanım Kılavuzu - Sayfa 5
Güvenlik Kamerası Ganz GH Series için çevrimiçi göz atın veya pdf Kurulum ve Kullanım Kılavuzu indirin. Ganz GH Series 16 sayfaları. Internal power supplies
Ayrıca Ganz GH Series için: Kullanım Kılavuzu (8 sayfalar)
Sayfayı Yazdır
IP67 rate
This product has been tested and certified compliant to IP67, and
under special order, meeting IP68. IP67 applied to this product has
a meaning that housing can momentary be submersed for less than
1 hour, at less than 1 meter without water leaking inside or with
complete dust proof protection.
THIS PRODUCT IS FULLY COMPLIANT WITH THE
FOLLOWING STANDARDS
EN 60529:1991
(IP rate)
EN 60065
(CE certification for EMC and safety)
EN 55022(1998)
EN 61000-3-2(1995)
EN 61000-3-2/A1(1998)
EN 61000-3-2/A2(1998)
EN 61000-3-3(1995)
EN 50130-4(1995)
EN 50130-4/A1(1998)
EN 60950-1 :2006 + A11 :2009
IMPORT ANT SAFEGUARDS AND WARNINGS
This
dangerous voltage constituting a
risk of electric shock is present
inside of this unit.
This symbol indicates that there
are important instruction that have
to be followed reported in the
manual to avoid risk to damage the
products or avoid hazardous risk to
maintenance
personnel.
Prior to proceed on installation and operation of the product, please
read and understand carefully all the indication and instruction
reported on this manual.
Please take note and observe the following warnings:
1.
Installation and servicing have to be done only by qualified
personnel and in compliant with local law.
2.
Use only parts or subassembly indicated in this manual
and original by CBC.
3.
After maintenance or repair/replacement of parts, please
proceed in a check where should be assured that none of
the exposed parts have not been connected to main power
or line circuitry.
4.
The installation method and materials have to be safe and
should be able to support minimum 4 times the weight of
camera/lens+housing and bracket weight combined
5.
After reading the manual, please preserve it for future
needs and use for servicing and maintenance operation
PRODUCT DESCRIPTION
This GH housing series is a dust-tight and waterproof enclosures
designed to protect a CCTV camera/lens combination for indoor
and outdoor application.
The GH housing series includes hidden pre-cabled protected
version kits to provide an easy and faster installation operation as
here under reported:
Model
GH-12KIT:
GH-24KIT:
GH-230KIT:
The GH housings are also available without hidden pre-cabled
protected assembly. The models available are the following:
Model
GH-12:
GH-24:
GH-230:
Accessories available:
GH-WM: Adjustable head and wall-mount bracket
GH-SM: Spacer/wall- mount adapter for side running of cables (just
for GH kits versions)
GH-SS: Sunshield
GH-PT: P/T plate adapter
GH-PA: Pole mount adapter
GH-PS 230/24: Internal transformer 230 Vac / 24 Vac
GH-PS 230/12: Internal power supply 230 Vac / 12 Vdc
GH-PS 24/12: Internal power supply 24 Vac / 12 Vdc
GH-PS 230/12H: Internal power supply 230 Vac / 12 Vdc, 1A
ENGLISH
symbol
indicates
that
and
service
Power Input accepted
12 Vdc
24 Vac
230 Vac
Power input accepted
12 Vdc
24 Vac
230 Vac
INSTALLATION AND OPERATION
Tools needed
In addition to the ones provided inside of the housing packaging,
the following tools are needed for a proper and fast operation:
Medium Phillips screwdriver
Medium blade screwdriver
Small blade screwdriver
5mm Allen ex
Sunshield remo ving/pivoting
To achieve and open the housing body, the first operation are
related to sunshield removing or pivoting.
The sunshield can be pivoted on both sides alternatively or
completely removed operating by the special Allen ex tool provided
into the housing packaging (see fig.1).
Back side body part removing
For safety regulation, the part of the body hosting power circuits
must be accessed by tool.
To remove this body part, operate on the (4) Phillips screws (see
fig.2).
Place the body part removed on the pivoted sunshield.
Front side body removing
This operation has to be done for camera/lens mounting and
servicing.
To open and remove the front side, operate on the (3) springs,
levering by the special polymeric tool provided with housing (see
fig.3). Once springs are released, slide the front body carefully and
leave pending. This part of the body is retention to the main body
by a safety cord for hand free operation.
Camera/lens assembling on housing
Coupling the camera and lens following respectively the indication
of their instruction manuals.
Due to the kind of lens used, camera or lens itself must be fixed on
housing plate.
We suggest to mount the camera/lens assembly as much close as
you can to the front window area (coincident with the camera/lens
mounting plate front borderline) considering the lens excursion in
case of zoom lens used.
Fix the camera/lens to the mounting plate Interleaving the insulated
washer (provided) between the ¼" screw and the upper side of the
plate.
Use the spacers provided for best axis front window view, if
needed.
Electrical Connection
Camera power supply
Connect the camera power input conductors to the appropriate wire
terminals of the power supply board situated on the back side of
the housing (see fig.4).
5
WARNING! The GH-230Kit and
GH-230 need a power supply at
230Vac. For safety reason, this
model must
be provided and
installed with sunshield even for
indoor
application.
This
requested to avoid any accidental
removal operation of the front body
part without the use of any tool that
proof
the
understanding
operation in progress and the
safety counter measures needed.
WARNING: the back side of the
housing body is destined to host
power supply circuits and terminal
strip connection with presence of
high voltage. Before opening this
side, please, switch off the line
source.
Warning:
to
avoid
electrical
hazardous, please, check all the
time the power supply source
voltage and camera requirements;
in case of discrepancies, use
appropriate optional Ganz power
supply board to provide correct
voltage to camera unit.
is
of