HIKVISION UD.6L0201D1443A01 Kullanıcı Kılavuzu - Sayfa 2
Güvenlik Kamerası HIKVISION UD.6L0201D1443A01 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. HIKVISION UD.6L0201D1443A01 2 sayfaları. Turret & dome camera
Sayfayı Yazdır
Figure 2-2 Fix the Mounting Base and the Camera
6.Adjust the camera according to the figure below
to get an optimum angle.
°
°
0 ~360
°
°
0 ~75
°
°
0 ~360
Figure 2-3 3-axis Adjustment
2.2 Installation of Type Camera
II
Steps:
1.Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
Mounting Base
Hole
Hole
Figure 2-4 The Drill Template
2.Fix the mounting base to the ceiling with the
supplied screws.
Figure 2-5 Fix the Mounting Base and Camera
3.Route the cables to the cable hole and connect
corresponding power cable and video cable.
4.Secure the camera to the mounting base.
5.Fix the enclosure to camera.
6.Attach the trim ring to the camera and rotate
it clockwise to secure the camera loosely.
°
°
0 ~360
°
°
°
0 ~75
0 ~360
Figure 2-6 3-axis Adjustment
2.3 Installation of Type
III
Steps:
1.Hold the mounting base, and rotate the lower
dome counterclockwise to disassemble the
lower dome and the black liner.
2.Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
Screw Hole
Drilling Template
Screw Hole
Figure 2-7 The Drill Template & Mounting
Base Installation
3.Route the cables to the cable hole and connect
the corresponding power cable and video cable.
4.Fix the mounting base to the ceiling with
the supplied screws.
355°
0-90°
355°
Figure 2-8 3-axis Adjustment
& Lower Dome
5.Adjust the Lens
1).Loosen the tilting lock screws besides the
lens.
2).Adjust the camera from the pan angle
°
°
°
(0 ~ 355 ); tilt angle (0 ~ 90 ), and rotate
°
°
the lens(0 ~355 ) to get the optimum angle.
3).Tighten the tilting lock screws.
6.Fit the black liner back to the camera.
7.Install the lower dome back to the camera and
rotate it clockwise to get it secured.
3 Menu Operation
Menu
VIDEO.
SETUP
LAUGUAGE
OUT
SCENE
LENS
EXPOSURE
BACKLIGHT
WB
DAY&NIGHT
NR
INDOOR
MANUAL
SHUTTER
BLC
ATW
COLOR
2D NR
OUTDOOR
AGC
HSBLC
AWC-SET
B/W
3D NR
INDOOR1
SENS-UP
INDOOR
EXT
LOW-
OUTDOOR
BRIGHTNESS
LIGHT
D-WDR
MANUAL
DEFOG
Figure 3-1 Main Menu
°
A coaxial camera controller (purchase separately)
is required to select the menu and adjust the
camera parameters.
3.1 VIDEO.OUT
Camera
PAL or NTSC is selectable .
3.2 LANGUAGE
English, Japanese, CHN1, CHN2, Korean, German,
French, Italian, Spanish, Polish, etc., are selectable.
3.3SETUP
3.3.1 SCENE
You can select indoor, outdoor, indoor 1 and low
-light as the working environments.
3.3.2 LENS
The camera is equipped with a fixed lens.
3.3.3 EXPOSURE
SHUTTER: AUTO,1/25, 1/50, FLK, 1/200, 1/400,
1/1k, 1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8, x10,
and x15 are selectable.
AGC
: You can set the AGC value from 0 to 15.
SENS-UP
: You can set the SENS-UP to OFF or AUTO.
BRIGHTNESS
: You can set the brightness value
from 1 to 100.
D-WDR
: You can set the D-WDR to ON to improve
the image quality or OFF to disable the function.
DEFOG
: You can set the defog function as ON to
enable the function. Position, size, and the defog
gradation are configurable.
EXPOSURE
1. SHUTTER
AUTO
2. AGC
OFF
3. SENS-UP
---
4. BRIGHTNESS
---|------ 40
5. DEFOG
OFF
6. BACKLIGHT
OFF
7. RETURN
RET
Figure 3-2 Exposure
3.3.4 Backlight
°
Backlight Compensation (BLC):
-GAIN:
Set the gain of BLC as High, Middle, or Low.
-AREA:
Press the up/down/left/right button to
define the BLC position and size. Select RET or
AGAIN to go back the BLC menu or re-define the
BLC area.
-Default:
Restore the BLC settings to the default.
HSBLC:
Select an HSBLC area. Set the DISPLAY status as ON.
Press the up/down/left/right button to define the
area position and size. Set the HSBLC LEVEL from 0
to 100. Select ALL DAY or Night for the HSBLC mode.
Set the BLACK MASK status as ON or OFF.
SPECIAL
ADJUST
RESET
CAM
EXIT
SHARPNESS
3.3.5 White Balance (WB)
TITLE
D-EFFECT
MONITOR
INDOOR, OUTDOOR, MANUAL, ATW (Auto-tracking
MOTION
LSC
White Balance), AWC→SET are selectable.
PRIVACY
3.3.6 Day & Night
DEFECT
Color, B/W, and EXT are selectable for DAY and
VERSION
NIGHT switches.
3.3.7 NR
2D NR
: You can set 2D NR status as ON or OFF.
3D NR
: Set the Smart NR status as ON and adjust
the 3D smart NR sensitivity ranges from 0 to 100.
Set the 3D NR LEVEL ranges from 0 to 100. Set the
START. AGC level as the threshold to enable AGC,
and set the END. AGC level as the threshold to
disable AGC.
2D&3D NR
1. 2DNR
OFF
2. 3DNR
ON
3. RETURN RET
Figure 3-5 NR
3.3.8 SPECIAL
Camera Title
: Edit the camera title on this section.
D-effect
:
-FREEZE
: Set the freeze function as ON or OFF.
-MIRROR
: OFF, MIRROR, V-FLIP, and ROTATE are
selectable for mirror.
-D-ZOOM
: Define the zoom area by configuring
the position from PAN & TILT.
-SMART D-ZOOM
and time are configurable.
-NEG.IMAGE
: Set the NEG IMAGE as ON or OFF.
SPECIAL
1. CAM TITLE
ON
2. D-DFFECT
3. MOTION
OFF
4. PRIVACY
OFF
5. LANGUAGE
ENG
6. DEFECT
7. VERSION
130722
HSBLC
8. RETURN
1. SELECT
AREA 1
Figure 3-7 Special
ON 8
2. DISPLAY
3. LEVEL
---|------ 40
Motion: Select a MOTION area. Set the DISPLAY
4. MODE
ALL DAY
5. BLACK MASK
ON
status as ON or OFF. Press the up/down/left/right
8
6. DEFAULT
button to define the position and size of the area.
7. RETURN
RET
Set the SENSITIVITY from 0 to 60. Set the MOTION
Figure 3-3 HSBLC
VIEW status as ON or OFF.
Privacy: Select a PRIVACY area. Set the DISPLAY
status as INV, MOSAIC, COLOR or OFF. Press the
up/down/left/right button to define the position
and size of the area.
Defect: LIVE DPC, STATIC DPC and Black DPC are
adjustable in this section.
Version
: You can check the software version of the
device.
PRIVACY
1. SELECT
AREA 1
2. DISPLAY
MOSAIC
3. COLOR
10
4. TRANS.
8
5. DEFAULT
6. RETURN
RET
Figure 3-9 Privacy Mask
3.3.9 ADJUST
Sharpness
: Adjust the sharpness from 0 to 15.
Monitor
: Monitor CRT, and Monitor LCD are
selectable.
LSC
: Set the LSC status as ON or OFF.
3.3.10 RESET
Reset all the settings to the default.
3.3.11 EXIT
Press OK to exit the menu.
3D NR
8
1. SMART NR
ON
2. LEVEL
------|--8 0
3. START. AGC -|--------10
8
4. END. AGC
-|--------10
5. RETURN
RET
Figure 3-6 3D NR
: The D-Zoom area, sensitivity
MOTION
8
1. SELECT
AREA 1
8
2. DISPLAY
ON8
3. SENSITIVITY
----|---- 30
8
4. MOTION VIEW ON
8
8
5. DEFAULT
6. RETURN
RET
RET
Figure 3-8 Motion Detection
ADJUST
8
--------|15
1. SHARPNESS
2. MONITOR
LCD8
3. LSC
OFF
1
4. VIDEO. OUT
PAL
5. RETURN
RET
Figure 3-10 Adjust