GREEN SERIES FITNESS CIR-TM6000DC-G Servis Kılavuzu - Sayfa 12
Koşu Bandı GREEN SERIES FITNESS CIR-TM6000DC-G için çevrimiçi göz atın veya pdf Servis Kılavuzu indirin. GREEN SERIES FITNESS CIR-TM6000DC-G 14 sayfaları.
4.6.
Engineering Mode SIX
t hen put back the safety key to enter mode.
」
4.6.1
Message window show
be control incline motor manually, press
4.6.2
Max incline display
「
I ncline Down
incline parameter
memory value, XXX=real time incline position parameter, press
Down
incline position, press
message window show
saving, press
4.6.3
Max incline parameter
memory value, XXX=real time incline position parameter, press
Down
incline position, press
message window show
after saving, press
4.6.4
Min incline parameter
memory value, XXX=real time incline position parameter, press
Down
incline position, press
message window show
saving, press
4.7
Engineering Mode SEVEN
Display
」
00= old output duty setting memory, XX=set duty value, press
t o set the duty, press
」
back to idle mode.(default=40, set range=35~80)
Program Update
5
5.1 Install software from PC
5.1.1
Un-zip the file labeled
5.1.2
Open the document then open the "PC-site Driver" document. Select file
0E6A030D_8051ISPICP_v3.00 the right click and select "Install (I)".
5.2 Programmer Update
5.2.1
Connect the programmer into the PC USB port. On the programmer, LED2 and LED3 will
illuminate.
www.GreenSeriesFitness.com
:
I ncline Test & Settings Pull out the safety key, press
M ANUAL INC XXX
『
m essage window show
:
」
t o set, set range:12~15, press
m essage window show
:
t o adjust the incline motor position, the parameter will be change according to
」
S tart
『
』
M IN AD OOO XXX
『
E nter
t o confirm and to next setting.(default=15)
「
」
:
m essage window show
t o adjust the incline motor position, the parameter will be change according to
」
S tart
『
』
M AX AD OOO XXX
『
「
E nter
」
t o confirm and to next setting.(default=195)
m essage window show
:
t o adjust the incline motor position, the parameter will be change according to
」
S tart
『
』
M IN AD OOO XXX
『
E nter
t o confirm and to next setting.(default=15)
「
」
F an Low Output Setting Pull out the safety key, press
:
t hen put back the safety key to enter mode. Message window show
S tart
w ait for a beep sound to save, press
『
』
Programmer v5.81
『
Programmer v5.81
©May 2015
CIR-TM6000DC-G Revision 1.1
, press
』
「
E nter
t o next setting.
「
」
M AX INCLINE XX
『
「
E nter
」
M IN AD OOO XXX
『
w ait for a beep sound to save the min incline parameter,
, the OOO and XXX value will the same after
』
『
M AX AD OOO XXX
w ait for a beep sound to save the max incline parameter,
, the OOO and XXX value will the same
』
M IN AD OOO XXX
『
w ait for a beep sound to save the min incline parameter,
, the OOO and XXX value will the same after
』
』
「
S top
」
+
「
I ncline Up
o r
I ncline Down
」
「
, press
I ncline Up
』
「
t o confirm and to next setting. Min
, OOO=old setting
』
I ncline Up
o r
「
」
「
』
, OOO=old setting
I ncline Up
o r
「
」
「
, OOO=old setting
』
I ncline Up
o r
「
」
「
F AN
「
F AN 00 XX
『
S peed Fast
o r
S peed Slow
「
」
「
E nter
t o confirm and
「
」
Call Toll free (800) 269-7140
I ncline Up
c an
」
or
」
I ncline
I ncline
I ncline
+
」
「
,
』
12