IKEA IUD9750WS1 Kurulum Talimatları Kılavuzu - Sayfa 3
Bulaşık Makinesi IKEA IUD9750WS1 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. IKEA IUD9750WS1 44 sayfaları. Undercounter dishwasher plastic giant tub models
Ayrıca IKEA IUD9750WS1 için: Kullanıcı Talimatları (25 sayfalar)
Sayfayı Yazdır
INSTALLATIONREQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
Tools needed
•
Pliers
•
Phillips screwdriver
•
Flat-blade screwdriver
•
_e" and 1¼,, n ut drivers or
hex sockets
•
Measuring tape or ruler
•
11/2"hole saw bit
•
Twist-on wire connectors
[proper size to connect
household wiring to 16-
gauge wiring in
dishwasher] (2)
•
15 TORX®t screwdriver
(if installing custom front
panels)
•
10" adjustable wrench
(opens to 11/8"[2.9 cm])
•
Utility knife
•
Level
•
Cordless drill
•
8/8"open-end wrench
•
Flashlight
•
Shallow pan
•
Wood block
•
Bath towel
Parts needed
•
90 ° elbow with 3/8"N.RT.
external threads on one
end. (The other end must
fit your water supply line.)
•
Teflon ®t tape or pipe joint
compound
Shims
#10 x 1/2"wood screws
[if installing custom front
panels] (4)
Tools needed (new installation)
•
Cordless drill
•
•
1/2",3/4"and 11/2"hole saw
•
bits
•
Small tubing center
Wire stripper
1V2" to 2" screw-type
clamp (if connecting to
waste-tee)
Parts needed (new installation)
•
Copper tubing (3/8"
•
recommended)
or
•
Flexible stainless steel
braided fill line
Clamp connector or
conduit connector
(to fit a 7/8"[2.2 cm]
diameter hole)
Parts supplied
B
A. Drain hose clamps [1 large and 1 small] (2)
B. #10 x 1/2" Phillips-head
screws (2)
C. Drain hose
_TORX is a registered
trademark of Acument
Intellectual
Properties,
LLC
<_Teflon is a registered trademark
of E.I. Dupont de Nemours and Company.
Additional
parts supplied (top-venting
models only)
•
Bottom sound pad (located in lower rack)
•
Moisture barrier tape
Make sure all these parts are included. If not, call
1-866-664-2449.
See separate parts list for accessories available for your
dishwasher.
ocoo
ec J smen s
Do not run drain lines, water lines or electrical wiring where they
can interfere with or contact the dishwasher motor or legs.
The location where the dishwasher will be installed must provide
clearance between motor and flooring. Motor should not touch
the floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher against
freezing. Damage from freezing is not covered by the warranty.
A side panel kit is available from your dealer for installing your
dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277) is available
from your dealer for installing underneath the countertop, but is
not required. Call 1-866-664-2449
for ordering.
Check location where the dishwasher will be installed. The
location must provide:
•
Easy access to water, electricity and drain.
•
Convenient access for loading and unloading dishes. Corner
locations require a 2" (5.1 cm) minimum clearance between
the side of the dishwasher door and the wall or cabinet.
•
Square opening for proper orientation.
•
Cabinet front perpendicular
to floor.
•
Level floor. If the floor at the front of the dishwasher is not level
with the rear of the opening, shims may be needed to level the
dishwasher.
NOTE: To avoid shifting during dishwasher operation, shims
must be securely attached to the floor.
If the dishwasher will be left unused for a period of time or it is in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the shaded area
shown in the "Cutout dimensions"
section.
Helpful Tip: If the floor in the dishwasher opening is uneven
(example: tile flooring only partway into opening), accurately
measure the dimensions and level the dishwasher.