Avantco 177MX60H Kullanıcı Kılavuzu - Sayfa 7

Mikser Avantco 177MX60H için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. Avantco 177MX60H 12 sayfaları. Gear driven 60 qt. commercial mixer

Sayfayı Yazdır

Operating Instructions for Normal Using

FIGURE 10

Set the timer #7 to the desired operating time between 1-30 minutes. The unit will NOT operate

unless the timer has been preset.

Close the safety guard #3. The unit will not operate if this guard and the bowl #6 are in the incorrect position.

The bowl can be lifted up and down using the bowl lift controls #10.

NOTE The bowl lift handle #5 is supplied loose and can be used to raise and lower the bowl in the

event of a power failure. THIS HANDLE MUST NOT BE FITTED IN NORMAL OPERATION.

Set the desired mixing speed using the handle #2, suitable for the attachment fitted and the product being

processed. Please refer to the mixing speed chart on page 8.

After the speed has been selected press the ON button #8. The unit will now run for the timed period set and

then switch OFF automatically.

The red emergency stop button if operated will shut down the machine at any time during the time cycle.

ALWAYS TURN OFF THE MACHINE BEFORE CHANGING SPEEDS. FAILURE TO DO SO MAY

DAMAGE THE GEARBOX AND VOID THE WARRANTY.

ALSO MAKE SURE THAT THE BOWL IS IN THE FULLY LIFTED POSITION AND THE SAFETY AND

THE SAFETY GUARD IS CLOSED.

Please ensure power supply matches your machine

Please ensure power supply matches your machine.

Low speed is position #1 and the knob will be facing forwards.

Please ensure power supply matches your machine

Medium speed is position #2 and the knob will be facing up.

Please ensure power supply matches your machine.

High speed position #3 and the knob will be facing down.

ALWAYS USE THE CORRECT ATTACHMENT FOR THE JOB.

before changing speed in order to avoid damage to the gear box

A. Whisk:

before changing speed in order to avoid damage to the gear box

before changing speed in order to avoid damage to the gear bo

before changing speed in order to avoid damage to the gear box

before changing speed in order to avoid damage to the gear bo

B. . Flat Beater:

before changing speed in order to avoid damage to the gear bo

Choose the different mixing devicews and speed.

Choose the different mixing devicews and

Choose the different mixing devicews and speed.

Choose the different mixing devicews and

in speed speed, working time isless than 15 minutes.

Using The Attachment Hub

in speed speed, working time isless than 15 minutes.

in speed speed, working time isless than 15 minutes

in speed speed, working time isless than 15 minutes.

in speed speed, working time isless than 15 minutes

work in middle speed, working time is less than 20 mins.

1. Turn the mixer off and remove any agitator attachment;

2. Loosen the hub mounting screw and remove the attachment hub cover;

work in middle speed, working time is less than 20 mins.

work in middle speed, working time is less than 20

3. Insert and align the attachment shaft into the attachment hub, ensure that the attachment is fully inserted;

work in middle speed, working time is less than 20 mins.

4. Tighten the hub mounting screw.

work in middle speed, working time is less than 20

is less than 30 minutes. Flour/ water quantity is 40%-50%.

NEVER RUN THE MIXER WITH HUB ACCESSORY AND AGITATOR AT THE SAME TIME

is less than 30 minutes. Flour/ water quantity is 40%-50%.

is less than 30 minutes. Flour/ water quantity is

is less than 30 minutes. Flour/ water quantity is 40%-50%.

is less than 30 minutes. Flour/ water quantity is

www.AvantcoEquipment.com

is less than 30 minutes. Flour/ water quantity is

Spatula

Dough Hook

Wisk

Bowl

• Any agitator is easily installed by sim-

ply raising it onto the mixing axle, and

the rotating it clockwise on the shaft

until into place. To remove, raise the

agitator on the shaft until it clears the

lock and then rotate counter-clockwise

and lower.

• All of tools are precisely fitted to the

bowl, rounded corners and easily

removable for cleaning.

• Any agitator is easily installed by sim-

ply raising it onto the mixing axle, and

the rotating it clockwise on the shaft

until into place. To remove, raise the

agitator on the shaft until it clears the

lock and then rotate counter-clockwise

and lower.

FIGURE 10

• All of tools are precisely fitted to the

bowl, rounded corners and easily

removable for cleaning.

Suitable for mixing liquids and soft ingredients, can work in all speeds.

Do not run for more than 15 minutes.

Suitable for mixing dry ingredients , can work in low & medium speeds only.

: According to the different mixing material.

Do not use in high speed. Do not run for more than 15 minutes.

: According to the different mixing material.

Dough Hook:

Suitable for mixing dough, can work in low speed only. Do not use in high speed.

: According to the different mixing material.

Do not run for more than 20 minutes. Absorption ratio must be more than 50%. Refer to mixer

: According to the different mixing material.

capacity chart.

Be suitable for mix and stir batter, eggs and work with

Be suitable for mix and stir stuffing and raw material, and

Middle position is suitable for mixing dough, working time

User Manual

FIGURE 10

Spatula

Dough Hook

Please ensure power supply matches your machine

Wisk

Please ensure power supply matches your machine.

Bowl

• Any agitator is easily installed by sim-

ply raising it onto the mixing axle, and

the rotating it clockwise on the shaft

until into place. To remove, raise the

agitator on the shaft until it clears the

before changing speed in order to avoid damage to the gear box

lock and then rotate counter-clockwise

and lower.

before changing speed in order to avoid damage to the gear bo

• All of tools are precisely fitted to the

bowl, rounded corners and easily

removable for cleaning.

Choose the different mixing devicews and speed.

• Any agitator is easily installed by sim-

ply raising it onto the mixing axle, and

Choose the different mixing devicews and

the rotating it clockwise on the shaft

until into place. To remove, raise the

agitator on the shaft until it clears the

Be suitable for mix and stir batter, eggs and work with

lock and then rotate counter-clockwise

in speed speed, working time isless than 15 minutes.

and lower.

Be suitable for mix and stir batter, eggs and work with

• All of tools are precisely fitted to the

in speed speed, working time isless than 15 minutes

bowl, rounded corners and easily

removable for cleaning.

Be suitable for mix and stir stuffing and raw material, and

work in middle speed, working time is less than 20 mins.

Be suitable for mix and stir stuffing and raw material, and

work in middle speed, working time is less than 20

Middle position is suitable for mixing dough, working time

is less than 30 minutes. Flour/ water quantity is 40%-50%.

Middle position is suitable for mixing dough, working time

is less than 30 minutes. Flour/ water quantity is

: Please stop machine first

speed.

Spatula

Dough Hook

Wisk

mins.

Bowl

mins.

• Any agitator is easily installed by sim-

ply raising it onto the mixing axle, and

the rotating it clockwise on the shaft

40%-50%.

until into place. To remove, raise the

agitator on the shaft until it clears the

40%-50%.

lock and then rotate counter-clockwise

40%-50%.

and lower.

: Please stop machine first

: According to the different mixing material.

speed.

40%-50%.

Please ensure power supply m

before changing speed in order t

: According to the diff

Choose the different mixing d

: According to the diff

Choose the different mixing d

Be suitable for mix and stir

in speed speed, working time

Be suitable for mix and stir

in speed speed, working time

Be suitable for mix and stir

work in middle speed, working

Be suitable for mix and stir

work in middle speed, working

Middle position is suitable fo

is less than 30 minutes. Flour/

Middle position is suitable fo

is less than 30 minutes. Flour/

mins.

Plea

befor

Choo

in sp

work