Makita 4341FCT Kullanım Kılavuzu - Sayfa 7
Elektrikli Alet Makita 4341FCT için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Makita 4341FCT 13 sayfaları. Jig saw
Ayrıca Makita 4341FCT için: Teknik Özellikler (2 sayfalar), Parça Dağılımı (3 sayfalar), Donanım Teknik Bilgileri (14 sayfalar)
Sayfayı Yazdır
ENGLISH
1
Tool opener
2
Blade clamp
3
Jig saw blade
4
Protrusions
5
Base
6
Hex wrench
7
Cutting action changing lever
8
Switch lever
9
Speed adjusting dial
10 Cutting line
SPECIFICATIONS
Model
Length of stroke............................................................. 26 mm
Cutting capacities
Wood ......................................................................... 110 mm
Steel .......................................................................... 10 mm
Strokes per minute (min
Overall length ................................................................ 271 mm
Net weight...................................................................... 2.4 kg
• Due to our continuing programme of research and
development, the specifications herein are subject to
change without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for the sawing of wood, plastic and
metal materials. As a result of the extensive accessory
and saw blade program, the tool can be used for many
purposes and is very well suited for curved or circular
cuts.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply.
They are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES
1.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2.
Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
3.
Do not cut hollow pipe.
4.
Do not cut oversize workpiece.
5.
Check for the proper clearance beyond the work-
piece before cutting so that the blade will not
strike the floor, workbench, etc.
6.
Hold the tool firmly.
7.
Make sure the blade is not contacting the work-
piece before the switch is turned on.
8.
Keep hands away from moving parts.
Explanation of general view
11 Bolt
12 Gear housing
13 V-notch
14 Bevel slot
15 Graduations
16 Starting hole
17 Dust nozzle
18 Hose for vacuum cleaner
19 Rip fence
20 Bolt
-1
) ............................................ 2,800
4341T
9.
Do not leave the tool running. Operate the tool
only when hand-held.
10. Always switch off and wait for the blade to come
to a complete stop before removing the blade
from the workpiece.
11. Do not touch the blade or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing saw blade (Fig.1, 2 & 3)
CAUTION:
• Always be sure that the tool is switched off and
unplugged before installing or removing the blade.
• Always clean out all chips or foreign matter adhering to
the blade and/or blade holder. Failure to do so may
cause insufficient tightening of the blade, resulting in a
serious injury.
• Do not touch the blade or the workpiece immediately
after operation; they may be extremely hot and could
burn your skin.
ENB062-1
• Tighten the saw blade securely. Failure to do so may
cause a serious injury.
Installing saw blade
Open the tool opener to the position shown in the figure.
(Fig. 1)
Keeping that situation, insert the saw blade into the blade
clamp as far as the two protrusions of the blade can not
be seen. (Fig. 2)
Return the tool opener to its original position. After
installing the saw blade, always make sure that the blade
is securely held in place by trying to pull it out.
CAUTION:
Do not open the tool opener excessively, or it may cause
tool damage.
21 Fence guide
22 Threaded knob
23 Circular guide pin
24 Rule bar
25 Guide rail adapter
26 Guide rail
27 Screw
28 Cover plate
29 Anti-splintering device
30 Hook
4341CT
4341FCT
26 mm
26 mm
135 mm
135 mm
10 mm
10 mm
800 – 2,800
800 – 2,800
271 mm
271 mm
2.4 kg
2.4 kg
7