Makita AF601 Kullanım Kılavuzu - Sayfa 3

Elektrikli Alet Makita AF601 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Makita AF601 13 sayfaları. Narrow crown stapler
Ayrıca Makita AF601 için: Kullanım Kılavuzu ve Kullanım Kılavuzu (13 sayfalar)

Sayfayı Yazdır

Safety devices

Make sure all safety systems are in working

order before operation. The tool must not oper-

ate if only the trigger is pulled or if only the contact

arm is pressed against the wood. It must work only

when both actions are performed. Test for possible

faulty operation with fasteners unloaded and the

pusher in fully pulled position.

Do not play with the contact element: it pre-

vents accidental discharge, so it must be kept

on and not removed. Securing the trigger in the

ON position is also very dangerous. Never attempt

to fasten the trigger. Do not operate a tool if any

portion of the tool operating controls is inoperable,

disconnected, altered, or not working properly.

Do not attempt to keep the contact element

depressed with tape or wire. Death or serious

injury may occur.

Always check contact element as instructed

in this manual. Fasteners may be driven acci-

dentally if the safety mechanism is not working

correctly.

Loading fasteners

Do not load the tool with fasteners when any

one of the operating controls is activated.

Use only fasteners specified in this manual.

The use of any other fasteners may cause mal-

function of the tool.

Power source

Never connect the tool to compressed air line

where the air pressure can exceed the suitable

air pressure range of the tool, specified in the

"SPECIFICATIONS" table, by 10%. Make sure

that the pressure supplied by the compressed air

system does not exceed the suitable air pressure

range of the tool. Set the air pressure initially to

the lower value of the suitable air pressure range.

When using the tool operated by compressed

air, particular attention must be paid to avoid

exceeding the maximum allowable pressure.

Operate the tool at the lowest pressure

required for the application, in order to prevent

unnecessarily high noise levels, increased

wear and resulting failures.

Never use the tool with other than compressed

air. If bottled gas (carbon dioxide, oxygen,

nitrogen, hydrogen, air, etc.) or combustible gas

(hydrogen, propane, acetylene, etc.) is used as a

power source for this tool, the tool will explode and

cause serious injury.

Always disconnect the air hose and remove all

of the fasteners:

—

when unattended;

—

before performing any maintenance or

repair;

—

before cleaning a jam;

—

before moving the tool to a new location.

Use only pneumatic tool oil specified in this

manual.

Operational safety

Always check the tool for its overall condition

and loose screws before operation. Tighten as

required.

Handle the tool carefully, as there is high pres-

sure inside the tool that can be dangerous if a

crack is caused by rough handling (dropping

or striking). Do not attempt to carve or engrave

on the tool.

Stop the operation immediately if you notice

something wrong or out of the ordinary with

the tool. An improperly functioning tool must not

be used.

Do not point the ejection port at anyone in the

vicinity. Keep hands and feet away from the

ejection port area.

Always assume that the tool contains

fasteners.

Never point the tool toward yourself or anyone

whether it contains fasteners or not.

Do not rush the job or force the tool. Handle

the tool carefully.

Do not activate the tool unless the tool is

placed firmly against the workpiece.

Never hold or carry the tool with a finger on the

trigger or hand it to someone in this condition.

Accidental firing can cause serious injury.

10. Never use fastener driving tools marked with

the symbol "Do not use on scaffoldings, lad-

ders" for specific application for example:

—

when changing one driving location to

another involves the use of scaffoldings,

stairs, ladders, or ladder alike constructions,

e.g. roof laths;

—

closing boxes or crates;

—

fitting transportation safety systems e.g. on

vehicles and wagons.

11.

Check walls, ceilings, floors, roofing and

the like carefully to avoid possible electrical

shock, gas leakage, explosions, etc. caused by

striking live wires, conduits or gas pipes.

12. Do not use the tool for fastening electrical cables.

It is not designed for electric cable installation and

may damage the insulation of electric cables thereby

causing electric shock or fire hazards.

13. Watch your footing and maintain your balance

with the tool. Make sure there is no one below

when working in high locations, and secure the air

hose to prevent danger if there is sudden jerking

or catching.

14. On rooftops and other high locations, drive

fasteners as you move forward. It is easy to lose

your footing if you drive fasteners while inching

backward. When driving fasteners against perpen-

dicular surface, work from the top to the bottom.

You can perform driving operations with less

fatigue by doing so.

15. A fastener will be bent or the tool can become

jammed if you mistakenly drive fastener on

top of another fastener or strike a knot in the

wood. The fastener may be thrown and hit

someone, or the tool itself can react danger-

ously. Place the fasteners with care.

16. Do not leave the loaded tool or the air com-

pressor under pressure for a long time out in

the sun. Be sure that dust, sand, chips and

foreign matter will not enter the tool in the

place where you leave it setting.

3 ENGLISH