ALIBI ALI-NS3022R Hızlı Kurulum Kılavuzu - Sayfa 2

IP Kamera ALIBI ALI-NS3022R için çevrimiçi göz atın veya pdf Hızlı Kurulum Kılavuzu indirin. ALIBI ALI-NS3022R 6 sayfaları.

Sayfayı Yazdır

Continue the installation with Connect camera drop cables to peripherals, LAN and power

below.

To mount the camera using the Junction box

Determine the best fasteners for securing the Junction box to mounting surface. The mounting

hardware provided is suitable for most surfaces.

Remove the junction box from the camera assembly by loosing the four captive screws.

Using the Junction box as a template, mark the location of the Junction box mounting screw holes. If

routing extension cables for the LAN, power, alarm devices, etc. through the mounting surface, mark

the location for that hole too. If installing the box onto a vertical surface, observe the orientation for

TOP and BOTTOM orientation markings inside the box.

Junction box

Orientation

Mounting screws (4)

markings

Drill holes in the mounting surface for the mounting screws and extension cables (if necessary).

Secure the Junction box to the mounting surface using appropriate fasteners.

Route the network LAN, power, ALARM, RS485, and AUDIO extension cables between the junction

box and the devices they connect to. Do not apply power to the extension cables at this time.

Attach the camera safety cable to the safety hook inside the junction box.

Safety cable hook

Safety cable

Camera

www.observint.com

Mounting screw hole

Wall insert (3)

Course-thread

Mounting screw (3)

Mounting surface

Camera to junction box

mounting screws (4)

To mount the camera onto an electrical box

Install a double-gang electrical box at the location where the camera will be installed.

Attach the adapter plate provided to the electrical box using four (4) screws.

Remove the junction box from the camera assembly by loosing the four mounting base captive

screws.

Attach the junction box to the adapter plate using four (4) screws.

Route extension cables from the power source and LAN switch (or LAN with PoE), and peripheral

devices for the left (or microphone) and right audio channels, and alarm input and output devices

into the electrical box, and then up through the cable opening in the adapter plate and junction box.

Attach the camera safety cable to the safety cable hook inside the junction box.

Step 3.

Connect camera drop cables to peripherals, LAN and

power

Camera mounting

base

Ethernet connector -

PoE capable

12 Vdc Power

connector

Camera drop cables to Ethernet, power and peripheral devices

Connect the network LAN, power, and ALARM and AUDIO peripheral cables to the camera drop

cables as needed. The camera can connect to one microphones, an alarm input sensor and an alarm

output (reporting) device, and to one audio line out device. Labels on the ALARM and AUDIO drop

cables show the which terminals are for signal and which are ground.

Connect the Ethernet LAN cable to the camera LAN drop cable. Protect the connection from

moisture and other contamination, if necessary. A weatherproof fitting is provided.

If the camera is not powered using PoE (Power over Ethernet injector), connect the 12 Vdc power

cable to the camera drop cable. The polarity of the drop cable connector is shown below.

Do not apply power to the camera at this time. Before applying power to the camera, ensure that



the polarity is correct. An incorrect connection may cause a malfunction and can damage the

CAUTION

camera.

Secure the camera to the mounting surface or Junction box using appropriate screws.

Apply power to the camera through the 12 Vdc power cable or PoE injector, as configured.

Step 4.

Install the Alibi Discovery Tool

Alibi Discovery Tool is a software utility used to "discover" Alibi cameras and NVRs/DVRs installed on the

physical Ethernet network (LAN) and change their network settings. Discovery Tool is provided on the CD

with your camera and is contained in Alibi Power Tools. To use Discovery Tool:

Insert the software CD provided with your camera into an optical drive on the Microsoft Windows

computer you will use to access your camera on the LAN.

On the CD, find the folder that contains the Alibi Power Tools (Alibi Tools Utility).

Install Alibi Power Tools. Refer to the ALIBI™ Power Tools Installation and User Manual also provided

on the CD. When the program opens, the following screen appears.

Cable access

Alarm IN/OUT

Terminals labels

Audio IN/OUT