ALIBI ALI-TS1012VR Hızlı Kurulum Kılavuzu
Dış Mekan Kamerası ALIBI ALI-TS1012VR için çevrimiçi göz atın veya pdf Hızlı Kurulum Kılavuzu indirin. ALIBI ALI-TS1012VR 2 sayfaları. 2.0mp hd-tvi ir outdoor turret camera
Sayfayı YazdırALI-TS1012VR 2.0MP HD-TVI IR
Outdoor Turret Camera Quick
Installation Guide
The ALIBI™ ALI-TS1012VR camera features a 2.0 MP high-performance CMOS imager that delivers sharp
1080p HD video. HD-TVI technology transmits zero latency HD video resolution over coax cabling.
Features
2MP CMOS image sensor
•
HD-TVI technology produces 1080p video for sharp, detailed images
•
3.6 mm wide angle (82.2°) lens captures images over large areas
•
65 ft Full Frame SMART IR
•
-40 °F ~ 140 °F extreme temperature operating range
•
IP66 weather-rated housing
•
Requires Alibi HD-TVI compatible recorder (HD-TVI DVR)
•
Optional installation with junction box ALI-AJ6 and flange adapter ALI-AF1
•
Mounting
plate
Clip plate
Enclosure
IR array
Lens
Camera
module
ALI-TS1012VR camera
ALI-CD1720P Camera drop cable connectors
What's in the box
Camera assembly
•
Mounting hardware
•
Security L- wrench
•
Drill template
•
This instruction guide
•
Tools you need
To install the camera, you will need:
12 Vdc power source. See Specifications for voltage and wattage requirements.
•
Tools and additional fasteners (may be required) for mounting the camera
•
Video and power extension cable
•
HD-TVI video setup monitor (optional)
•
Installation
The camera can be attached directly to a ceiling or wall, or installed with the ALI-AJ6 junction box or
ALI-AF1 flange adapter.
www.observint.com
1
Before installation:
•
•
•
•
During installation:
•
•
•
1.
HD-TVI video
BNC Connector
Power
Connector
2.
3.
Make sure that the device is in good condition and all the assembly parts are included.
Check the specification of the products for the installation environment.
Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
To avoid fire or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the Specifications section.
Camera Lens: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
array shield becomes soiled, clean it only with approved products. See the
Monitor impedance: Set the monitor impedance switch to 75 Ω.
Power supply: Camera drop cable: The camera drop cable includes two connectors:
Video BNC connector: For transmission of the HD-TVI video signal across a coax (75 Ω)
—
extension cable.
Power connector: When applying Vdc power, observe the power polarity. See the picture to the
—
right for connector polarity configuration.
Remove the mounting plate from the camera assembly
Loosen the clip plate captive screw with the L-wrench provided.
u
Slide the clip plate out as shown in the photo above.
v
Separate the mounting base from the enclosure.
a.
If mounting the camera directly to a wall or ceiling:
i.
Using the mounting plate or drill template provided with your camera, mark the
location of the screws that anchor the base plate to the mounting surface. If you are
routing the drop cable through base, also mark the position of the hole for the drop
cable.
ii.
Drill holes for the screws. The mounting hardware provided is appropriate for most
surfaces. However, depending on the surface materials, more appropriate fasteners
may be required.
iii.
Drill a 3/4" hole for the drop cable, if necessary. The drop cable can be routed through
the mounting surface, or through a cable channel in the mounting plate.
b.
If mounting the camera using the ALI-AJ6 junction box:
i.
Separate the ALI-AJ6 mounting plate from the back box.
ii.
Using the back box as a template, mark the location of the screws that will hold the
back box to the mounting surface.
iii.
Drill holes for the screws. The mounting hardware provided is appropriate for most
surfaces. More appropriate fasteners may be required.
iv.
Drill a 3/4" hole for the drop cable, if necessary. The drop cable can be routed through
the mounting surface, or through a conduit adapter in the side of the back box.
v.
Anchor the back box to the mounting surface.
vi.
Attach the camera mounting plate to the ALI-AJ6 mounting plate.
c.
If mounting the camera using the ALI-AF1 flange adapter:
i.
Attach the camera mounting plate to the ALI-AF1 flange adapter.
Route camera video and power extension cables between camera location and the monitoring
device (HD-TVI DVR).
Connect the camera drop cable to video and power extension cables.
section.
Cleaning
u
Enclosure
Clip plate
v
ALI-TS1012VR_CQ
161004