Corsa 14866BLK Kurulum Talimatları Kılavuzu - Sayfa 4
Havalandırma Davlumbazı Corsa 14866BLK için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Corsa 14866BLK 6 sayfaları. Cat back exhaust system for chevrolet silverado 2014; chevrolet silverado 2015; chevrolet silverado 2016; chevrolet silverado 2017; gmc sierra 1500 2014; gmc sierra 1500 2015; gmc sierra 1500 2016; gmc sierra 1500 2017
Sayfayı YazdırInstallation of CORSA Exhaust System:
NOTE:
Apply the anti-seize lubricant (supplied) to the threads ONLY of all the clamps and flange bolts. Failure to follow this
procedure can cause nuts to seize on clamps and potentially destroy threads. After applying anti-seize lubricant, be sure to
thoroughly clean your hands, as lubricant will tarnish stainless steel. All clamps should be tightened using a properly calibrated
Torque Wrench. Using an air impact gun will damage the clamp and reduce its ability to
effectively seal the joint. It may also cause the joint to separate, thereby causing damage
to your exhaust system and to your vehicle.
NOTE:
Align all clamps so that the center of the clamp bolt is 90 degrees from the notch in
the pipe. (See Fig. CLAMP)
1. Begin by reinstalling the spherical clamp onto the end of the factory Y pipe. Install it
such that the bolt is on the driver's side of the pipe while the hex head is toward the
ground to more easily facilitate tightening. (Fig A)
2. Locate the headpipe and insert the hanger into the rubber grommet. (Fig B) Insert the spherical form of the headpipe into the
spherical clamp and adjust the headpipe such that the part of the hanger inside the rubber grommet is level and parallel to the
ground. (Fig C). Use a temporary spacer between the headpipe and frame rail, and snugly tighten the spherical clamp using the
ratchet and 13mm socket. (Fig D).
For 143.5" wheel base trucks, skip to Step #4. For 153" wheel base trucks, continue to Step #3.
3. Locate the short, straight length of pipe with the expansion on one end. Slide a 3.5" clamp over the expansion and then slide it
over the outlet end of the headpipe. Orient the clamp such that the bolt is on the driver's side of the pipe with the nut towards
the ground. Snugly tighten the clamp using the ratchet and 15mm socket. (Fig E).
4. Locate the muffler and another 3.5" clamp. Slide the clamp over the expanded inlet of the muffler and then slide the muffler
onto either the end of the headpipe (143.5" WB trucks) or the end of the 153" adapter pipe (153" WB trucks). Make sure the
drain hole in muffler is oriented downwards. Snugly tighten the clamp using the ratchet and 15mm socket. (Fig F)
5. Locate the tail pipe and another 3.5" clamp. Slide the clamp over the expansion and from the rear of the vehicle, feed the pipe
over the rear axle. Insert the hangers into the rubber grommets both near the muffler and the single hanger near the end of
the tail pipe. Adjust the tail pipe such that the portion of the hangers inside the grommets are level and parallel to the ground.
Snugly tighten the clamp using the ratchet and 15mm socket. (Fig G)
6. Locate another 3.5" clamp and the tip assembly. Slide the clamp over the expansion and then slide the tip assembly onto the
tail pipe. Adjust rotation of tip assembly to align the tips with the rear bumper and the side of the truck bed. Snugly tighten the
clamp using the ratchet and 15mm socket. (Fig H)
7. Ensure the exhaust system is adjusted properly making sure the headpipe is not contacting any bracing, the axle pipe is not
contacting the rear axle or chassis, and that the tip is adjusted to preference. Once satisfied, beginning at the front of the
vehicle, fully tighten down all clamps using a torque wrench. Tighten the spherical clamp using the 13mm socket to 31ft-lb and
the 3.5" clamps to 45ft-lb using the 15mm socket. Make sure to remove the temporary spacer from Step #2 at this time if it is
still in place.
Cat Back Exhaust System
Single Side Exit w/ Twin 4.5" Pro-Series Tips
2014+ Chevrolet Silverado/GMC Sierra 1500 6.2L
143.5" & 153" Wheel Base
PN: 14866, 14866BLK