GARDEN MASTER GM1515 Montaj Talimatları - Sayfa 2

Dış Mekan Depolama GARDEN MASTER GM1515 için çevrimiçi göz atın veya pdf Montaj Talimatları indirin. GARDEN MASTER GM1515 2 sayfaları. Sloping roof shed

Sayfayı Yazdır

If you feel confident that you do not need to read through these instructions, see page 2....

If you choose to vary from these instructions your warranty will be impaired.

Basic overview of what I am trying to achieve...

"For those of us who do not like reading instructions...."

Just join the sheets together and fit the channels to the top and bottom of the sheets as a

framing to make 4 walls and the roof. Follow these basic steps:....

Front Wall

: Layout (D) door with the 715mm sheet attached. Cap the sheet with (F) channels

(2 sided cutout - Top and 1 sided cutout - bottom). Protrude the channels out past the door. Fit

Door spacers to make sure door fits gap OK (they sit on top of the jambs) Drill & Fix (Rivet or

screw) at every 2nd rib. Attach door spacer at each end thru door jambs and channels. 3 fixings

underneath into sheeting pan and door jambs top and bottom. Fit padbolt.

Back

: Join 2 (A) 1830mm Sheets together. Cap with (F) Channels and fix thru every 2nd rib

and at least 1 fixing per sheet thru the back of the channel into the pan of the sheeting.

Roof

: Join 2 (A) 1830mm Sheets together. Cap with (E) Channels. Fix @ every 2nd rib. Attach (G) 1830 "L"s

to ribs at each end of sheeting at corners and 600mm apart in between.

End walls

: Join the 2 (B) sheets together that slope the same way. Cap with (E) channels and fix at corners

and every 2nd rib in between. 2 -3 fixings up underneath into pan of sheeting, top and Bottom.

Assembly

: You have now made up your panels. It's just, Join the corners and put the roof on! Make sure

you have at least 6 fixings down each corner when you join the walls. Fix one side of the roof on thru the (G)

"L" into the top channel on one end wall approx 500mm apart. Check overhang and fix to the other end wall.

You now need to fix down thru every 2nd pan in the roof into the top channels on the front and back walls.

More in high wind areas. Please make sure that you have removed all swarf filings as the rust spots that

they produce may hinder any warranty claims.

Generally most fixings are spaced at 300mm apart

Keep fixings in the pans as close to the ribs as possible for added strength.

Ribs will always protrude to the outside of the shed.

Extra internal fixings is strongly recommended in high wind areas.

Detailed instructions with diagrams:....

1: Front Wall

Note that the cutouts go to the inside of the panel to allow

easy fitment of end walls on assembly

You will need:

(D) Pre-hinged door and sheet

(F) 1 top and 1 bottom Channel

(H) 2 x Door spacers

To hinge the door on the opposite

side - simply put the top channel on

the bottom and bottom on top.

Inside

(H)

Outside

A.Slip (C) Corner door jamb

under door as shown. Use (H)

door spacer to determine the

correct opening size by placing

Spacer

on the bottom flange of the door

jambs. Then fit (F) channels to

tops and bottoms of sheeting.

Channel

January 09

Rib

Pan

Drawings are diagrammatic and are

not necessarily to detail.

(F) Channels with cut-

outs (as shown).

(H)

(D)

Channels will come short of ends of corner

door jamb and sheeting by 10 - 15mm on all

panels

B. Outside: Fix channel at corners

and every 2nd rib between and

thru door jambs and spacer

C. Inside: One fixing per sheet at

each end up thru channel under-

side and thru door jambs/spacer

D. Fit padbolt to the outside of

door.

Note: Higher side of

Fix through top and bottom of

channels into Door jamb & spacer

channel goes to inside

of shed

Door jamb on inside

Pg 2

If you feel confident that you do not need to read through these instructions, see page 2....

If you choose to vary from these instructions your warranty will be impaired.

2: Back Wall

You need:

2 x (F) Channels

2 x (A) Sheets

(F)

3: Roof

You need:

2 x (E) Channels

2 x (A) Sheets

2 x (G) "L"s

(E)

4: End Walls

You need:

2 x (B) Sheets - Left

2 x (B) Sheets - Right

2 x (E) Channels

(B)

(E)

A. Join 2 Left (B) sheets together to give a slope at the top.

B. Cap sheeting with (E) 1515mm channels.

C. Fix the channels at the corners and every 2nd rib in between.

D. 3 fixings up underneath thru channel into pan of sheet

E. Perform the same again for the Right side.

A. Join 2 (A) sheets together with 2

fixings thru the overlapping ribs

making sure the ends of the sheets

are flush.

B. Cap sheeting with (F) channels put-

(F)

ting the cutouts top and bottom

same as the front wall.

C. Fix the channels thru the end ribs

and every 2nd rib between.

(A)

D. Make sure you put at least 1 fixing

per sheet up thru the underside of

the channel into the pan of the

sheet.

A. Join 2 (A) sheets together same

(E)

B. Cap sheeting with (E) channels.

(G)

C. Fix the channels every 2nd rib

D. Place the short flange of the "L"

(A)

(G)

Door Brace Kit

A. The Door braces can be fitted now or after

you have assembled your shed.

(E)

B. Tuck one end of the "Z" between the bot-

tom channel of the inside of the door and

the sheet. Do the same at the top overlap-

ping in the centre behind the padbolt. If you

have a locking "T" handle you will have to

run the "Z"s the opposite way to the dia-

gram.

C. Fix the "Z"s at the ends and in the centre to

the channel it is tucked under and thru the

overlap in the centre. 2 or 3 more rivets will

be required thru the door sheeting into the

Channels will end

"Z", but they will need to be fixed through

15 - 20mm short

at tops of end

from the outside of the

walls and 10 - 15

door for neater appear-

at bottoms

ance.

D. You may need to cut or

bend the flange at the bot-

tom and top of the "Z" if

it catches on door jamb

when opening or closing.

January 09

Pg 3

as the back.

but not the corners at this stage

on top of the rib at 1 end. Make

sure ends are flush with sheeting

and put 1 fixing in the centre to

hold the "L". Fix the corners

thru the channels and 1 more

between the corner and the

centre fixing. Perform the same

at the other end. 5 fixings ea "L"

Inside

Padbolt

"Z" Brace