KitchenAid 3183659 Kurulum Talimatı - Sayfa 4

Fırın KitchenAid 3183659 için çevrimiçi göz atın veya pdf Kurulum Talimatı indirin. KitchenAid 3183659 7 sayfaları. Electric built-in 24” and 27” thermal single and double ovens 24” and 27” thermal convection single and double ovens

Sayfayı Yazdır

Electrical

requirements

connection

Electrical Shock Hazard

Electrical ground is required on this

appliance.

If cold water pipe is interrupted by

plastic, non-metallic gaskets, or other

insulating materials, Do Not use for

grounding.

Do Not ground to a gas pipe.

Do Not have a fuse in'the neutral or

grounding circuit. A fuse in the neutral

or grounding circuit could result in an

electrical shock.

Do Not use an extension cord with

this appliance.

Check with a qualified electrician if

you are in doubt as to whether the

appliance is properly grounded.

Failure to follow these in instructions

could result in serious injury or death.

If codes permit and a separate grounding

wire is used, it is recommended that a

qualified electrician determine that the

grounding path is adequate.

IMPORTANT:

Save Installation Instructions

for the

local electrical inspector's use.

This appliance

must

be connected to

the proper electrical voltage and

requency as specified on the serial/rating

plate

located behind the oven door on the front

frame. Models rated at 7.0 kw on 240 volts (5.3

kw on 208 volts) or more require a separate 40-

ampere circuit. Models rated at 3.6 kw on 240

volts (2.7 kw on 208 volts) or less require a

separate 30-ampere circuit. Fuse both sides of

the line. A time-delay fuse or circuit breaker is

recommended.

OVEN MUST BE CONNECTED

WITH COPPER WIRE ONLY.

Wire sizes and connections

must

conform to the reauirements

of the

National Electrical Code, ANSI/NFPA

70 - latest

edition**, and all local codes and ordinances.

Wires sizes and connections

must conform with

the rating of the appliance.

Copies of the standards listed may be obtained

from:

**National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

This appliance should be connected

directlv to the fused disconnect

(or

circuit breaker box) through flexible, armored or

non-metallic

sheathed, copper cable (with

grounding wire). The flexible armored cable

from the appliance should be connected directly

to the junction box.

Locate the junction box to allow as

much slack in the cable as possible

between the junction box and the appliance so

that the oven can be moved if servicing is ever

necessary.

Do Not cut the conduit.

A U.L.-listed conduit connector

must

be provided at the junction box.

A wiring diagram is included in the

Tech Sheet. The Tech Sheet is located

behind the control panel.

Electrical Shock Hazard

Electrical ground is required on this

appliance.

Do Not connect to the electrical supply

until appliance is permanently

grounded.

Disconnect power to the junction box

before making the electrical

connection.

This appliance must be connected to a

grounded, metallic, permanent wiring

system, or a grounding connector

should be connected to the grounding

terminal or wire lead on the appliance.

Failure to do so could result in a fire,

personal injury or electrical shock.

This appliance is manufactured

with white

(neutral) power supply wire and a cabinet-

connected green grounding wire twisted

toget her.

Connect the appliance cable to the junction box

through the U.L.-listed conduit connector.

Complete electrical connection according to

local codes and ordinances.

A. Where local codes permit...

connecting the cabinet-grounding

conductor

to the neutral (white) junction box wire:

Cable from

Junction

power supply

box \

Bare or /

II'

green wire

conduit

Figure 1

Cable-

from oven

connect01

Grounded Neutral

1. Disconnect the power supply.

2. Remove the terminal block cover.

3. Connect together 3 wires: green and white

appliance cable wires and the neutral (white)

wire in junction box.

4. Connect the two black wires together; then

the two red wires together. See Figure 1.

B. Where local codes Do Not

permit...

connecting the cabinet-grounding

conductor

to the neutral (white) junction box wire:

Red

wires

Cable from

Bare

green

wires

isted

Cable

conduit

from oven

connector

Figure 2

Ungrounded Neutral

1. Disconnect power supply.

2. Separate the green and white appliance

cable wires.

3. Connect the white appliance cable wire to the

neutral (white) wire in the junction box.

4. Connect the two black wires together; then

the two red wires together. See Figure 2.

5. Connect the green or bare grounding wire

from the appliance cable to a grounded wire in

the junction box.

C. If connecting

to a four-

wire electrical

system...

Do Not connect the cabinet-grounding

conductor to the neutral (white) junction

box wire.

Cable from

Figure 3

conduit

connector

1. Disconnect the power supply.

2. Separate the green (or bare) and white

appliance cable wires.

3. Connect the white appliance cable wire to the

neutral (white) wire in the junction box.

4. Connect the two black wires together; then

the two red wires together. See Figure 3.

5. Connect the green appliance cable wire to

the green grounding wire in the junction box.

Panel C