Jandy AquaPure Ei Series Manuel - Sayfa 4

Su Filtrasyon Sistemleri Jandy AquaPure Ei Series için çevrimiçi göz atın veya pdf Manuel indirin. Jandy AquaPure Ei Series 8 sayfaları. Replacement kits for models apure35plg / 35plgc
Ayrıca Jandy AquaPure Ei Series için: Talimatlar (4 sayfalar)

Sayfayı Yazdır

Page 4

8. Connect the Output Cable wires to the Power PCB

(see Figure 12).

9. Securely connect the cell leads to the like colored

terminals (see Figure 7).

Black

Red

Figure 7.

Connecting Cell Leads

10. Reattach the terminal cap.

11. Reattach the cover to the back plate using the four

(4) mounting screws.

12. Reattach the outer dress cover.

13. Reconnect the power.

4. Power Pack Wiring Instructions

WARNING

When using electrical products, basic precautions

should always be followed, including the following:

•

DANGER: RISK OF ELECTRIC SHOCK WHICH

CAN RESULT IN SERIOUS INJURY OR DEATH.

Before attempting installation or service, ensure

that all power to the device is disconnected/

turned off at the circuit breaker. Connect only

to a circuit protected by a ground-fault circuit-

interrupter (GFCI).

•

Grounding is required. The unit should be

installed by a qualified service representative

and should be properly grounded and bonded

(See Section 4.B, Bonding).

•

To avoid property damage, serious injury or

death, never use the chassis backplate of the

power pack to ground any other equipment.

•

Install to permit access for servicing.

•

Please read all cautions and safety instructions

in the Important Safety Instructions section of the

Jandy

AquaPure

(H0331400). Before attempting any electrical

wiring, be sure to read and follow safety

instructions. Wiring should only be attempted

by a qualified professional.

Jandy

Pro Series AquaPure

Red

Blue

Series owner's manual

Ei™ Series

Replacement Kit Instructions

A. Wiring the Power Pack to the Power

Source

1. Wire power pack to pool pump power source using

3.3 mm

(12 AWG) insulated wire and conduit. The

power pack should be connected to the pump motor

switch or automatic timer (pool pump timer) as

shown in Figure 12.

2. Attach the third wire (ground) from the electrical

panel to the ground point inside the power pack.

Bonding per Section 4.B must also be accomplished

to ensure personal safety and safety of equipment.

B. Bonding

The National Electrical Code

pool equipment to be bonded to each other. Check

your local codes to determine if the NEC and/or

other local installation codes are enforced by the

Authority Having Jurisdiction (AHJ). A solid,

copper 8.37 mm

(8 AWG) wire is recommended,

per the NEC, for bonding the power pack to a

permanent bonding connection that is acceptable to

the local AHJ. Refer to your locally enforced codes

for the acceptable bonding wire gauge. Attach the

bonding point located on the bottom of the chassis

backplate to a common bonding point. Do not use

the power pack as the common bonding point.

Each piece of non-related pool equipment requiring

a ground should also be bonded to the common,

approved bonding point. There should be one

bonding connection to the power pack. In Canada,

the Canadian Electrical Code (CEC) dictates that

the bonding conductor be, minimum 13.3 mm

AWG).

C. Connection to an AquaLink

Control System or PDA (Optional)

The Jandy AquaLink RS or PDA is a multi-function

pool controller which can fully control the function

of the Jandy AquaPure Ei chlorine generating device.

Adjustment of the chlorine production rate can be

controlled from the main menu of the Jandy AquaLink

RS or PDA. The AquaLink RS or PDA offers individual

pool and spa settings for output percentage. Refer to

the AquaLink RS or PDA Owner's Manual for more

information.

NOTE The Jandy AquaPure Ei chlorine generating

device will communicate with all AquaLink

models Rev. K or later.

(NEC

) requires