KitchenAid KEBU208SSS - 30" Double Wall Oven Kurulum Talimatları Kılavuzu - Sayfa 2
Fırın KitchenAid KEBU208SSS - 30" Double Wall Oven için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. KitchenAid KEBU208SSS - 30" Double Wall Oven 20 sayfaları. 30" (76.2 cm) electric single and double built-in oven
Ayrıca KitchenAid KEBU208SSS - 30" Double Wall Oven için: Boyut Kılavuzu (1 sayfalar)
Sayfayı Yazdır
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
Adjustable wrench or
Phillips screwdriver
Flat-blade screwdriver
Measuring tape
Hand or electric drill (for wall cabinet installations)
1" (25 mm) drill bit (for wall cabinet installations)
Level
Copper tubing cutter
Parts supplied (1 box, 3 plastic bags)
One -
" stem to
" quick connect
Two -
" elbow to
" quick connects
Water filter
#10–16 x
" screw and 1 mounting ring (to mount water filter)
#8–14 x 1" screws - single oven (2), double oven (4)
Bottom vent (supplied on some models)
#8–18 x
" screws - bottom vent (supplied on some models)
Parts needed
UL listed or CSA approved conduit connector
UL listed wire connectors
Tubing staples/retainers
2
BUILT-IN OVEN SAFETY
Your safety and the safety of others are very important.
INSTALLATION REQUIREMENTS
" wrench
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
¼" O.D. copper tubing (to make water connection)
NOTE: Due to temperatures around oven, copper tubing is
required.
Water connection device (to connect ¼" O.D. copper tubing
to water source). Check local codes for type of connection
required.
¼" to ¼" water supply union (between copper tubing from the
filter and copper tubing attached to oven)
Check local codes. Check existing electrical supply. See
"Electrical Requirements."
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
Built-In Oven Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance with oven.
Recessed installation area must provide complete enclosure
around the recessed portion of the oven.
Grounded electrical supply is required. See "Electrical
Requirements" section.
Electrical supply junction box should be located 3" (7.6 cm)
maximum below the support surface when the oven is
installed in a wall cabinet. A 1" (2.5 cm) minimum diameter
hole should have been drilled in the right rear or left rear
corner of the support surface to route the oven conduit
through to the junction box.
NOTE: For undercounter installation, it is recommended that
the junction box be located in the adjacent right or left
cabinet. If you are installing the junction box on rear wall
behind oven, the junction box must be recessed and located
in the upper or lower right or left corner of the cabinet;
otherwise, the oven will not fit into the cabinet opening.