Gardena 14630 Operatör El Kitabı - Sayfa 7

Çim Biçme Makinesi Gardena 14630 için çevrimiçi göz atın veya pdf Operatör El Kitabı indirin. Gardena 14630 14 sayfaları. Battery lawnmower

Sayfayı Yazdır

2. ASSEMBLY

DANGER! Risk of physical injury!

Cut injury when the product starts accidentally.

v Wait for the blade to stop, remove the safety key and use

gloves before you assemble the product.

To assemble the lower handles [ Fig. A1 ]:

1. Push the lower handles

(1)

into the openings

Make sure that the handles

(1)

holes are inline up with the holes in the mower.

2. Put the screws

(3)

in the holes in the mower.

(3)

3. Tighten the screws

To assemble the upper handle [ Fig. A2 ]:

The upper handle

(4)

can be assembled to the lower handle

3 positions to adjust the height.

v Working position: Adjust the height of the handle so that you are

in an upright position when using the mower.

Position

Height of the handle above the ground

Lower hole

91 cm

Middle hole

94 cm

Upper hole

97 cm

(4)

1. Put the upper handle

on the lower handles

Make sure that the handles are completely in place and the desired

holes are inline.

2. Put the screws

(5)

through the holes.

(6)

3. Put the washers

and the wing nuts

4. Tighten the wing nuts

(7)

To attach the cable to the handle [ Fig. A3 ]:

(8)

v Attach the cable

to the handle with the clamps

Make sure that the cable is not locked between the lower and the

upper handle.

To assemble the grass box [ Fig. A4 ]:

1. Push the cover

(11)

on the grass box

Make sure that all latches are connected.

2. Push the handle

(12)

into the cover

3. OPERATION

DANGER! Risk of physical injury!

Cut injury when the product starts accidentally.

v Wait for the blade to stop, remove the safety key and use

gloves before you adjust or transport the product.

To charge the battery [ Fig. O1 / O2 / O3 ]:

CAUTION!

Note the mains voltage! The voltage of the power source must

match the voltage specified on the rating plate of the charger.

For the GARDENA Battery Mower Art. 14630-55 there is no battery

and no charger in the scope of delivery.

Thanks to the intelligent charging process, the charge condition of the

battery is automatically detected and then charged up with the optimal

charge current depending on battery temperature and voltage.

In this way, the battery is treated with care and remains permanently fully

charged when it is stored in the charger.

1. Open the cover

(19)

of the battery holder

(A)

2. Push the locking button

and remove the battery

(D)

holder

3. Connect the battery charger

(C)

(2)

in the mower.

are completely in place and the handle

(1)

(7)

(5)

on the screws

(9)

(10)

until the latches click.

(11)

until it clicks.

(D)

(B)

from the battery

into a mains socket.

4. Slide the battery charger

When the battery charge indicator

the battery is being charged.

When the battery charge indicator

permanently green the battery is completely charged

(Charging time, see 7. TECHNICAL DATA).

5. Examine the charge status regularly while you charge.

6. When the battery

(B)

battery

from the charger

Meaning of the indication elements:

Indication on the charger [ Fig. O3 ]:

Flashing of the Battery

The charging procedure is indicated by flashing of the battery charge

(Lc)

Charge Indicator

indicator

Note: The charging procedure is only possible when the battery

temperature is within the allowable charging temperature range,

see 7. TECHNICAL DATA.

Continuous Lighting

Continuous lighting of the battery charge indicator

of the Battery

the battery is fully charged or that the temperature of the battery is

(Lc)

Charge Indicator

not within the allowable charging temperature range and can therefore

not be charged.

When the battery is not inserted, continuous lighting of the battery

charge indicator

socket outlet and that the battery charger is ready for operation.

To adjust the cutting height [ Fig. O4 / O5 ]:

DANGER! Risk of physical injury!

Cut injury when the front and rear wheel axles are adjusted in

different height positions.

v Adjust the front and rear wheel axles on both sides in the

same height position.

The cutting height can be adjusted in 3 positions (35, 50, 65 mm).

1. Lay the product on its side carefully.

2. Pull the front wheel axle

3. Release the front wheel axle

Make sure that the front wheel axle is fully released on both sides in the

same height position.

4. Pull the rear wheel axle

5. Release the rear wheel axle

Make sure that the rear wheel axle is fully released in the height adjust

opening.

To use the mower with the grass box [ Fig. O6 ]:

DANGER! Risk of physical injury!

Cut injury when the blade turns or the mower starts

accidentally.

v Wait for the blade to stop, remove the safety key and use

gloves before you open the protective flap

v Do not put your hands in the discharge opening.

1. Lift the protective flap

2. Hang the grass box

Make sure that the grass box is securely connected.

3. Start the mower.

4. When the grass box

5. Lift the protective flap

6. Remove the grass box by the handle

7. Empty the grass box

To start the mower [ Fig. O1 /O7 ]:

DANGER! Risk of physical injury!

Risk of injury if the product does not stop when the

start lever is released.

v Do not bypass the safety devices or switches. For example do

not attach the start lever to the handle.

(C)

onto the battery

(B)

(Lc)

at the charger flashes green

(Lc)

at the charger illuminates

is completely charged, you can disconnect the

(C)

(Lc)

indicates that the mains plug is inserted in the

(13)

out of the current height adjust openings

(13)

in the new height adjust openings

(15)

out of the current height adjust opening

(15)

in the new height adjust opening

(17)

(10)

into the mower by the handle

(12)

(10)

is full, stop the mower.

(17)

(12)

(10)

(Lc)

indicates that

(14)

(16)