Gardena 1471 Kullanım Talimatları Kılavuzu - Sayfa 3

Su Pompası Gardena 1471 için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Gardena 1471 7 sayfaları.

Sayfayı Yazdır

For safety reasons we recommend that you always operate

the Dual Pump via a residual-current device (DIN VDE 0100-702

and 0100-738).

v Please contact your electrician.

In Austria, according to ÖVE B / EN 60 555 part 1 to 3, pumps

In Austria

which are used in swimming pools and garden ponds, and

equipped with firm power cable should be fed via an ÖVE

approved isolating transformer – rated voltage must not exceed

230 V.

In Switzerland

In Switzerland mobile appliances which are used outdoors,

must be connected via a residual-current device.

Mains power

According to DIN VDE (German Electrical Engineers' Associa-

tion) 0620, mains power cables must not have a smaller cross-

section than the rubber-sheathed cables of the designation

H07 RNF. The cable length must be at least 10 m.

Data indicated on the type plate must match technical data of

the mains supply.

v Take care that the electrical connections are made within

dry area, protected from flooding.

Protect plug and power cable from heat, oil and sharp edges.

v Don't use the power cable for plugging off.

The power cable must not be used for mounting or relocating

the pump. For submerging or lifting / securing the pump, fix a

rope (available from GARDENA Service) to the pump's carrying

handle.

Extension cables must meet the requirements of DIN VDE

0620.

Visual check

v Before operating the pump, first make a visual check, if there

is any damage of the pump (esp. regarding power cable and

plug).

v Observe the minimum water level and the max. delivery

height (see 9. Technical Data).

A damaged pump must not be used.

v In case of damage, please have the pump checked by our

GARDENA Service Centre.

Note on use

v Clear the outlet line before use.

When setting up the pump for use out of water

Dry-Running

In order to avoid dry-running of the pump, take care that the

end of the suction hose is always submerged into the liquid.

v Before each operation, fill the pump to overflowing with

approx. 2 l of the liquid to be pumped !

Liquid fails to flow

Sand and other abrasive substances in the liquid cause in-

creased wear and reduce the pump's output.

v Use a Pump Preliminary Filter if the water contains sand

(Art. No. 1730 / 1731).

The pump should not run against the closed delivery side

for more than 5 minutes.

If liquid fails to flow, switch off the pump immediately.

Minimum flow rate

The minimum flow rate is 80 l / h (= 1.3 l / min).

Watering accessories with lower rate must not be operated.

Hot water –

If the pump is operated for prolonged periods of time (> 5 min)

risk of scalding

with the delivery side closed, the water in the pump may heat up

so that there is a risk of scalding yourself with hot water.

v The pump should not run against the closed delivery side for

more than 5 minutes.

v If liquid fails to flow, switch off the pump immediately.

3. Initial Operation

Connecting a filter or

1. When setting up the pump for use underwater, screw the

hose to the inlet side :

filter

– or –

When setting up the pump for use out of water, connect a

vacuum-resistant suction hose

tion

connection is air-tight.

2. When setting up the pump for use out of water with suction

heights over 4 m, the suction hose should also be secured (fas-

tened to a wooden peg for example).

The pump is relieved of the weight of the suction hose.

Don't use any hose connection system fittings on the suction

side ! A vacuum-resistant suction hose must be used

• e.g. GARDENA Suction Unit, art. no. 1411.

In order to reduce the suction time, it is advisable to use a suction

hose with backflow preventer avoiding automatic draining of the

suction hose when the pump is stopped.

Both pump connectors

Connection hose

thread to which 13 mm (1/ 2"), 19 mm (3 / 4") and 16 mm (5 / 8")

to delivery side :

hoses can be connected by using GARDENA hose connection

system fittings.

Best results regarding the delivery capacity of the pump are

achieved when connecting 19 mm (3 / 4") hoses in conjunction

with e.g.

• GARDENA Pump Connection Set, art. no. 1752,

or when using 25 mm (1") hoses with fittings available from your

sanitary dealer.

v Connect the pressure hose

delivery side.

Only when setting up the pump for use out of water :

Filling

V Before each operation, fill the pump to overflowing

the pump :

1. Unscrew the screw fitting

2. Fill the pump via the filler cap

2 l of the liquid to be pumped.

3. Tighten the screw fitting

use pliers).

onto the connection

at the inlet side of the pump.

with filter to the connec-

at the inlet side of the pump and screw on so that the

are equipped with a 33.3 mm (G 1")

to the connector

on the

with approx. 2 l of the liquid to be pumped !

of the filler cap

by hand.

to overflowing with approx.

of the filler cap

by hand (do not