KitchenAid 30" Freestanding Range Kurulum Talimatları - Sayfa 3

Havalandırma Davlumbazı KitchenAid 30" Freestanding Range için çevrimiçi göz atın veya pdf Kurulum Talimatları indirin. KitchenAid 30" Freestanding Range 5 sayfaları. (61cm), (68.6cm), and (76.2cm) indoor/outdoor electric warming drawer
Ayrıca KitchenAid 30" Freestanding Range için: Kurulum Talimatları Kılavuzu (8 sayfalar), Kurulum Talimatları (5 sayfalar), Kurulum Talimatları Kılavuzu (13 sayfalar), Kurulum Talimatları Kılavuzu (16 sayfalar)

Sayfayı Yazdır

4-wire wall

3-wire wall

receptacle

(14-50R)

receptacle

Figure 1

(1 o-50R)

Figure 2

Four-wire installation is recommended

requirement for mobile homes:

This

appliance is manufactured with ground

connected to cabinet.

The ground must be revised so

the green grounding wire of the four-wire power supply

cord is connected to the cabinet.

When a four-wire receptacle of NEMA type 14-50R is

used (See Figure l), a matching U.L.-listed, four-wire,

250~volt, 40-ampere, range power supply cord (pigtail)

must be used. This cord contains four copper conductors

with ring terminals on the appliance end, terminating in a

NEMA Type 14-50P plug on the supply end. The fourth

(grounding) conductor must be identified by a green or

green/yellow cover and the neutral conductor by a white

cover. Cord should be Type SRD or SRDT with a U.L.-

listed strain relief and be at least four feet long.

The

MINIMUM

conductor sizes for the copper

four-wire power supply cord are:

40-ampere circuit

2, No.-8 conductors

1, No.-10 white neutral

1, No.-8 green grounding

JD.I

Three-wire installation if a four-wire

system is not available:

Local codes may

permit the use of a U.L.-listed, 250-volt,

40-ampere range power supply cord (pigtail). This cord

contains three, No.-10 copper wires and matches a

three-wire receptacle of NEMA Type lo-50R, shown in

Figure 2. Connectors on the appliance end must be ring

terminals. A U.L.-listed strain relief must be used to

connect the power supply cord to the range.

E-l

This range should be connected directly to

the fused disconnect or circuit breaker box

through flexible, armored or non-metallic

sheathed, copper cable (with grounding wire). Locate the

junction box to allow two to three feet of slack in the line

so that the range can be moved if servicing is ever

necessary.

Do Not cut the conduit.

A U.L.-listed conduit connector

must

be provided at each

end of the power supply cable (at the range and at the

junction box).

Wire sizes and connections must conform to

the requirements of the National Electrical

Code, ANSVNFPA 70 -

latest edition (*, see

Panel A) and all local codes and ordinances

for the kilowatt rating of the range (40-amperes).

IG I

The wiring diagram is also located on the

back of the range.

Now start...

with range in kitchen.

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to follow this instruction could result in

back or other injury.

When moving range, slide range onto cardboard or

hardboard to prevent damaging the floor covering.

Ll-l

Put on safety glasses and gloves. Remove

shipping materials, tape and protective film

from range. Keep cardboard bottom and

shipping base under range. Remove oven racks and

parts package from inside oven.

Take four cardboard

corners from the carton. Stack one

cardboard corner on top of another. Repeat with other

two corners. Place them lengthwise on the floor behind

the range - to support the range when it is laid on its

back. Firmly grasp the range and gently lay it on its back

on the cardboard corners.

Pull cardboard shipping base firmly to remove.

141

Use an adjustable wre

the leveling legs four c

Place cardboard or hardboard in front of

range. Stand range back up onto cardboard

or hardboard.

Electrical Shock Hazard

Disconnect power to the junction box before making

connection.

Electrically ground range.

Failure to follow these instructions could result in

death, fire or electrical shock.

This range must be connected to a grounded,

metallic, permanent wiring system, or a grounding

connector should be connected to the grounding

terminal or wire lead on the range.

cover

l-6-l

Remove the terminal block cover located on

the back of range.

/71

Depending on your electrical supply, make

the four-wire or three-wire connection to the

range following the "Power supply cord

method" or "Direct wire method" instructions.

knockout

opening,

for 40-

ampere

power

supply

cord

knockout

opening

for power

s,ubppdy

Figure 3

Disconnect the power supply.

2. Remove the knockout for the 40-ampere power supply

cord.

3. Assemble a U.L.-listed strain relief in the opening.

4. Insert the power supply cord through the strain relief,

allowing enough slack to easily attach the wiring to the

terminal block.

5. Use only ring-type terminals to connect the power

supply. To secure the power supply cord, use the 3/8"

brass nuts attached to the knockout opening. Be sure

nuts are installed tight.

6. Complete electrical connection according to your type

electrical supply ("Four-wire electrical connection" or

"Three-wire electrical connection").

Four-wire electrical connection:

I -

grounding link

Y3' Screw

Figure 4

Use this method for mobile homes and whenever

four-wire installation is required.

7. Remove the grounding-link screw from the range

frame. Save the grounding-link screw. Bend up the

grounding link so that it does not contact the range.

See Figure 4.

3. Connect the neutral (center wire) wire to the center,

silver-colored terminal screw on the terminal block

using the brass nuts that are attached to the

terminal block cover. See Figure 6.

10. Connect the other two wires to the outer terminals

on the terminal block. See Figure 6.

11.

Do Not loosen the factory installed nuts already

on the terminal.

Tighten nuts with 3/8" nut driver

for proper electrical connection.

12. Tighten the strain relief screws.

13. Replace the terminal block cover.

green

grounding

wire

Figure 5

8. Connect the green grounding wire from power

supply cord to the range using the grounding-link

screw.

The grounding wire must be attached first

and must not contact any other terminal. See

Figure 5.

silver-

relief and 40-ampere

Three-wire electrical connection:

silver-

line l/r

---

U.L.-listed

strain relief

and 40-ampere

range

power supply

cord

Figure 7

Use this method ONLY if local codes PERMIT

connecting cabinet-grounding

conductor to neutral

wire of power supply cord.

7. Use the brass terminal nuts attached to the

terminal block cover to connect the neutral wire

(center wire) to the silver-colored terminal

screw on the terminal block. See Figure 7.

8. Connect the other two wires to outer terminal

screws on the terminal block. See Figure 7.

9. Do Not loosen factory-installed nuts already on

the terminal.

Tighten nuts with 3/8" nut driver

for proper electrical connection.

lO.Tighten the strain relief screws.

11 .Reinstall the terminal block cover.

Disconnect the power

supply.

2. Remove the knockout for the

power supply cable.

3. Assemble a U.L.-listed conduit

connector in the power supply

cable opening.

4. Strip outer covering back

3 inches from end, exposing the wires. Strip the

insulation back 1 inch from the end of each wire.

5. Form the bare wire into a

"U" shaped hook.

6. Insert the power supply

7=i

cable through the conduit

connector, allowing enough

slack to easily attach the

-m

1" -WI

wiring terminal block.

7. Complete electrical connection according to your type

electrical supply ("Four-wire electrical connection" or

"Three-wire electrical connection").

Panel B