KitchenAid GZ7930XHS1 Kullanım ve Bakım Kılavuzu - Sayfa 3

Havalandırma Davlumbazı KitchenAid GZ7930XHS1 için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu indirin. KitchenAid GZ7930XHS1 16 sayfaları. 30"/36" retractable downdraft vent systems

Sayfayı Yazdır

IMPORTANT: Observe all

governing

codes and ordinances.

It is the customer's

responsibility:

eTo contact a qualified

electrical

installer.

• To assure that the electrical

installation

is adequate

and in

conformance

with National

Electrical Code, ANSI/NFPA 70

-- latest edition*,

or CSA

Standards

C22.1-g4, Canadian

Electrical Code, Part 1 and

C22.2 No. 0-M91 - latest

edition**

and all local codes

and ordinances.

If codes permit and a separate

ground wire is used, it is

recommended

that a qualified

electrician

determine

that the

ground

path is adequate.

Do not ground to a gas pipe.

Check with a qualified

electrician

you are not sure downdraft

vent is

properly

grounded.

Do not have a fuse in the neutral

or ground

circuit.

IMPORTANT: Save installation

instructions

for electrical

inspector's

use.

A 120-volt,

60-Hz, AC-only,

fused

electrical

supply

is required

on a separate

15 amp

circuit.

time-delay

fuse or circuit

breaker

is recommended.The

fuse

must

be sized per local

codes

accordance

with

the electrical

rating

of the downdraft

vent

specified

on the model/serial

rating

plate

located

on the front

of the downdraft

vent

above

the

wiring

box cover.

The downdraft

vent must

be connected

with copper wire

only.

Wire sizes and connections

must conform

to the

requirements

of the National

Electrical

Code, ANSI/NFPA 70 --

latest edition*,

or CSA Standards

C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. 0-M91

- latest edition**

and all local

codes and ordinances.

WARNING -- TO REDUCE THE

RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO

PERSONS, OBSERVE THE

FOLLOWING:

installation work and electrical

wiring must be done by qualified

person(s) in accordance with all

applicable Codes and Standards,

including fire related construction.

Sufficient air is needed for proper

combustion and exhausting of

gases through the flue (chimney)

of fuel burning equipment to

prevent back drafting. Follow the

heating equipment

manufacturer's guideline and

safety standards such as those

published by the National Fire

Protection Association

(NFPA),and the American Society

of Heating Refrigeration and Air

Conditioning Engineers

(ASHRAE), and the local code

authorities.

When cutting or drilling into wall

or ceiling, do not damage

electrical wiring and other hidden

utilities.

Ducted fans must always be

vented to the outdoors.

WARNING --To

reduce the risk

of fire, use only metal ductwork.

This unit must be grounded.

This downdraft

vent should

be connected

directly to the fused

disconnect

(or circuit

breaker)

through

flexible,

armored

or non-

metallic

sheathed,

copper cable.

Allow some slack in the cable so

the downdraft

vent can be moved

if servicing

is ever necessary.

E.,

A U.L.- or C.S.A,-listed,

1/2"

(12.7 mm) conduit connector

must be provided

at each end of

the power supply cable (at the

downdraft

vent and at the

junction

box).

Awiring

diagram

is located

on the downdraft

vent base

above the wiring

box cover.

Copies of the standards

listed may be

obtained

from:

* National

Fire Protection

Association

One Batterymarch

Park

Quincy, Massachusetts

02269

**CSA International

8501 East PleasantValley

Road

Cleveland,

Ohio 44131-5575