KitchenAid KIRD807HSS0 and Kurulum Talimatları ve Kullanım ve Bakım Kılavuzu - Sayfa 2
Havalandırma Davlumbazı KitchenAid KIRD807HSS0 and için çevrimiçi göz atın veya pdf Kurulum Talimatları ve Kullanım ve Bakım Kılavuzu indirin. KitchenAid KIRD807HSS0 and 14 sayfaları. 30" and 36" retractable downdraft vent systems
Sayfayı Yazdır
Your safety and the safety of
others are very important,
We have provided many important
safety messages in this manual
and on your appliance. Always
read and obey all safety
messages.
This is the safety alert
symbol.
This symbol alerts you to
potential hazards that can kill or
hurt you and others.
All safety messages will follow the
safety alert symbol and either the
word "DANGER" or "WARNING".
These words mean:
You can be killed or seriously
injured if you don't immediately
foltow
instructions.
You can be killed or seriously
injured if you don't foltow
instructions.
All safety messages will tell you
what the potential hazard is, tell you
how to reduce the chance of injury,
and tell you what can happen if the
instructions are not followed.
mmportant:
Observe
aH governing
codes and ordinances,
Proper installation
is your
responsibility.
Make sure you have
everything
necessary for correct
installation.
It is the responsibility
of the installer to comply with the
installation
clearances
specified
on
the model/serial
rating plate.The
model/serial
rating plate is located
on the front of the downdraft
vent
above the wiring
box cover.
Mobile home installation
The installation
of this range hood
must conform
to the Manufactured
Home Construction
Safety
Standards, Title 24 CFR, Part 328
(formerly
the Federal Standard
for
Mobile
Home Construction
and
Safety, Title 24, HUD, Part 289) or
when such standard
is not
applicable,
the Standard
for
Manufactured
Home Installation
1982 (Manufactured
Home Sites,
Communities
and Setups) ANSI
A225.1/NFPA 591A*, or latest
edition,
or with local codes.
Check location where downdraft
vent will be installed.The
location
should be away from strong draft
areas, such as windows,
doors
and strong heating vents or fans.
Before making countertop
cutout,
check that downdraft
vent and
cooktop
location will clear cabinet
walls, backsplash,
and rear wall
studs inside cabinet.
ALL OPENINGS IN THE WALL OR
FLOOR WHERE RETRACTABLE
DOWNDRAFT VENT iS TO BE
INSTALLED MUST BE SEALED.
Electrical
ground is required.
See
"Electrical
requirements;'
page 3.
When installing
downdraft
vent,
the cabinet drawer will need to be
removed
and the drawer front
installed
permanently
to cabinet.
Note: Downdraft
vent is installed
directly
behind the cooktop. Install
downdraft
vent first.
Cabinet construction:
Downdraft
vent is designed
for use in a
cabinet with a depth of 24"
(61 cm). Some installations
require a countertop
deeper than
25" (63.5 cmL See chart on page 5.
The maximum
depth of the
overhead
cabinet is 13" (33 cm).
Overhead
cabinets
installed at
either side of the downdraft
vent
must be 18" (45.7 cm) above the
cooking surface.
See cooktop
Installation
instructions
before making any
cutouts and for the minimum
distance between the front edge
of the countertop
and front edge
of cooktop.The
minimum
horizontal
distance
between the
overhead
cabinets
is the same as
the width of the installed
downdraft
vent.
When installing
a 36" (91.4 cm)
retractable
downdraft
vent with
"Create-A-Cooktop"
modules,
the
optional
support must be installed
on the front of the downdraft
vent.
See installation
steps for details.
Parts supplied
for installation:
• t top trim
2 end cape
• 2 lower support
legs
2 overcounter
support
brackets
2 undemounter
mounting
brackets
• 1 bag of fasteners
t meta_ cover
• 1 backdraft
damper
• literature
package
• optional
support
and two screws
(36" (91.4 era) models
only
Parts needed
for installation:
• 2 U.L.= or C.S.A.4isted
1/2" (12.7 ram)
conduit
connectors
(3 are required
if
the exterior-mounted
vent motor
is
used.}
• 1 wall cap for interior-mounted
motor
• vent system
• power supply
cable
• wiring
cable for optiona_ remote b_ower
kit.
Tools needed for
installation:
• safety glasses
• g_oves
• jig or keyhole saw
• drill with 118" drill bit
• pencil
• measuring
tape
• flat=b_ade screwdriver
• Phillips
screwdriver
• 318" (9.5 ram} nut driver
or ratchet
• leve_
• pliers
• metal snips
• wire stripper
or utility knife
caulking
gun
and weatherproof
caumk
• duct tape