KitchenAid KHHC2090SSS4 Kurulum Talimatları Kılavuzu - Sayfa 7
Mikrodalga Fırın KitchenAid KHHC2090SSS4 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. KitchenAid KHHC2090SSS4 12 sayfaları. Microwave hood combination
Ayrıca KitchenAid KHHC2090SSS4 için: Kullanıcı Talimatları (8 sayfalar)
Sayfayı Yazdır
The microwave
oven must be installed on a minimum
of 1 wall
stud, preferably 2, using a minimum
of 1 lag screw, preferably 2.
1.
Using measuring
tape, find and clearly mark the vertical
centerline
of the opening.
A
}L___o
_
A. Centerline
2. Align the centerline of the wall template with the centerline on
the wall, making sure it is level, and that the top of the wall
template abuts the bottom edge of the upper cabinet. Tape
the wall template into place.
NOTES:
•
If the front edge of the upper cabinet is lower than the back
edge, lower the wall template so that its top is level with the
front edge of the cabinet.
•
If the wall template is damaged or unusable, measure and
mark the wall with the dimensions described in Step 4.
.ll
A
................................................................
C
B
A. Rear wall
B. Wall template
C. Top of wall template must align with
front edge of cabineL
D. Front edge of upper cabinet
3. Mark both end holes of the mounting plate through the wall
template.
4. Remove the wall template and check the markings:
Upper cabinet bottom
t
'
t
i
i
i
i
151/2.
Centerline
18%6"
(39.4 crn)
i
(46.5 crn)
i
14V8"
i
14Va"
J-
(3 .9
om)-- l
//2._.2 .............................
L............................
'....... 2 .........
/
1
Bottom of mounting plate
Mounting plate end hole
,
5=
The bottom edge line must be 18sAe '' (46.5 cm) from the
bottom of the upper cabinet, and must be level.
The end holes must be 151/2 '' (39.4 cm) from the bottom
edge of the upper cabinet, and must be on a level line with
each other. They must each be 141/8 '' (35.9 cm) from the
centerline.
With the support tabs facing forward (see illustrations in
"Locate Wall Stud(s)" section), align the mounting plate center
markers to the centerline on the wall, making sure its bottom
edge is aligned to the horizontal line drawn in Step 3, and that
the end holes are properly marked. Make sure the mounting
plate is level.
6.
Holding the mounting plate in place, find the wall stud
centerline(s) drawn in Step 2 of "Locate Wall Stud(s)," and
mark at least 1, preferably 2 hole(s) through the mounting
plate, closest to the wall stud centerline(s). See figures 1, 2
and/or 3 in "Possible Wall Stud Configurations"
in "Locate
Wall Stud(s)" section. The blackened holes in the shaded
areas are ideal hole locations.
7. Set the mounting plate aside.
Wall Venting Installation
Only
Upper cabinet bottom
_ %" (1 cm)
8.
9.
10.
11.
12.
13.
14.
f
f
4" (10.2 cm)
CenterJine
* I
6" (15.2 era)
6" (15.2 era)
Mark the centerline 3/8" (1 cm) down from the bottom edge of
the upper cabinet.
Using measuring tape, measure out 6" (15.2 cm) on both sides
of the centerline, and mark.
Measure down 4" (10.2 cm) from the mark made in Step 8,
and mark.
Using a straightedge, draw the 2 horizontal, level lines through
the marks made in steps 8 and 10.
Draw the 2 vertical, plumb lines down from the marks made in
Step 9 to complete the 12" x 4" (30.5 x 10.2 cm) rectangle.
This is the venting cutout area.
Cut a 3/4" (19 mm) hole in one corner of the cutout area.
Using a keyhole saw, cut out the venting cutout area.
In addition to being installed on at least 1 wall stud, the mounting
plate must attach to the wall at both end holes. If the end holes
are not over wall studs, use two 1/4-20 x 3" round-head bolts with
toggle nuts; if 1 end hole is over a wall stud, use 1 lag screw and
one 1/4-20 x 3" round-head bolt with toggle nut; or if both end
holes are over wall studs, use 2 lag screws. Following are
3 installation configurations.
1=
2.
Installation for No Wall Studs at End Holes
(Figures I and 2)
Drill 3/4" (19 mm) holes through the wall at both end holes
marked in Step 3 of "Mark Rear Wall."
Drill 3/16" (5 mm) hole(s) into the wall stud(s) at the hole(s)
marked in Step 6 of "Mark Rear Wall." Refer to figures 1 and 2
in "Possible Wall Stud Configurations"
in "Locate Wall Stud(s)"
section.
Installation for Wall Stud at One End Hole (Figure 3)
1. Drill a 3/16" (5 mm) hole into the wall stud at the end hole
marked in Step 3 of "Mark Rear Wall."
2. If installing on a second wall stud, drill a 3/16" (5 mm) hole into
the wall stud at the other hole marked in Step 6 of "Mark Rear
Wall." Refer to Figure 3 in "Possible Wall Stud Configurations"
in "Locate Wall Stud(s)" section.
3. Drill a 3/4" (19 mm) hole through the wall at the other end hole.
Installation for Wall Studs at Both End Holes (Figure 4)
1. Drill 3/16" (5 mm) holes into the studs at the end holes marked
in Step 3 of "Mark Rear Wall."