Gardena AccuJet Li-18 Kullanım Talimatları Kılavuzu - Sayfa 4
Üfleyici Gardena AccuJet Li-18 için çevrimiçi göz atın veya pdf Kullanım Talimatları Kılavuzu indirin. Gardena AccuJet Li-18 16 sayfaları. Accu blower
Ayrıca Gardena AccuJet Li-18 için: Kullanım Talimatları Kılavuzu (16 sayfalar), Operatör El Kitabı (10 sayfalar), Kullanım Talimatları Kılavuzu (18 sayfalar), Kullanım Talimatları Kılavuzu (17 sayfalar), Kullanım Talimatları Kılavuzu (17 sayfalar)
Sayfayı Yazdır
e) The electric cord must be uncoiled.
Coiled cord can overheat and reduce the
efficiency of the product. Always wind
cord carefully, avoiding kinks.
f) Only use the charger provided with your
unit when charging the battery.
Use of any other charger could permanently
damage the battery, charger and/or the blower
unit.
g) If operating a power tool in a damp
l ocation is unavoidable, use a residual
current device (RCD) protected supply
with a tripping current of not more than
30 mA. Even with a RCD installed,
100 % safety cannot be guaranteed and
safe working practices must be followed
at all times. Check your RCD every time
you use your product.
Use of an RCD reduces the risk of electric
shock.
3) Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication.
A moment of inattention while operating
power tools may result in serious personal
injury.
b) Use personal protective equipment.
Always wear eye protection and hearing
protection. To prevent dust irritation,
the use of a dust mask is recommended.
Protective equipment such as eye protection,
hearing protection, dust mask, nonskid safety
shoes, or hard hat used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting.
Battery-powered units do not have to be
plugged into an electrical outlet to operate;
therefore, they are always in operating mode.
Ensure the switch is in the off position
before connecting to battery charger, picking
up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
d) Do not overreach. Keep proper footing
and balance at all times. On slopes, be extra
careful and wear non-slip footwear. Do not
walk backwards while operating your
product. Walk, never run. Do not use ladders
while operating the product.
This enables better control of the power tool
in unexpected situations.
e) Dress properly. Always wear suitable
clothing, gloves, and stout shoes.
Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
4) Power tool use and care
a) Only use the product in the manner and for
the functions described in these instructions.
Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Always make sure your product is in a safe
operating condition before use. Do not use
the power tool if the switch does not turn it
on and off. Know how to stop the product
quickly in an emergency. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) The impeller continues to rotate after
your product has been switched off.
The motor must be stopped and the impeller
blade no longer turning to avoid serious injury
from the rotating blades.
d) Remove battery from unit:
– before leaving the product unattended for any
period;
– before clearing a blockage;
– before checking, cleaning or working on the
appliance;
– if the product starts to vibrate abnormally.
Check immediately. Excessive vibration can
cause injury.
– before passing to another person.
e) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
f) Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage of
parts and any other condition that may affect
the power tool's operation. If damaged, have
the power tool repaired before use. Keep all
cooling air inlets clear of debris.
Many accidents are caused by poorly maintained
power tools.
g) Use the power tool and accessories in
accordance with these instructions, taking
into account the working conditions and the
work to be performed. Use the product only
in daylight or good artificial light. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
17