AC Hydraulic VLT12 Kullanıcı Kılavuzu - Sayfa 3
Jacks AC Hydraulic VLT12 için çevrimiçi göz atın veya pdf Kullanıcı Kılavuzu indirin. AC Hydraulic VLT12 16 sayfaları. Hydraulic transmission jack capacity 1200 kg
Ayrıca AC Hydraulic VLT12 için: Kullanıcı Kılavuzu (16 sayfalar)
VLT12
GB
WARNING -
safe usage instructions
1. The use of this jack is limited to the removal, instal-
lation, and transportation in the lowest position, of
transmissions and differentials.
2. It may be used - WITHIN THE WEIGHT LIMITA-
TIONS SPECIFIED - with appropriate adaptors
manufactured especially for the jack to handle other
components, such as rear axle units and transfer
cases.
3. Be sure that the vehicle is appropriately supported
and chocked before starting repairs.
4. Avoid decentral placement of the gravity of the
load. Decentral placement of the load might cause
overturning of or damage to the transmission jack.
5. Always make sure, that the biggest stage of the
telescopic cylinder is fully extended, before applying
a load on the jack. Otherwise, there may be a sudden
equalization in which the ram is dropping, while the
middle cylinder goes up. This is to be avoided by -
when the jack reaches the load – to continue pumping
until you feel a clear increase in load.
6. All transportation must take place in the lowest
position.
7. Do not overload. Overloading may cause damage
to or failure of the jack.
8. This jack is designed for use only on hard level sur-
faces capable of sustaining the load. Use on other
than hard level surfaces may result in jack instabi-
lity and possible loss of load.
9. The safety valve being adjusted and sealed by the
manufacturer shall not be additionally adjusted.
10. Failure to heed these warnings may result in loss
of load, damage to jack, and/or failure resulting in
personal or property damage.
Assembling:
1. Tighten the legs loosely by means of the 4 bolts (49)
and the 2 long through-going bolts (55).
2. Mount wheels with discs on legs and tighten to a
torque setting of 80 Nm.
3. Place jack on level surface to make pump rest on
the 2 through-going bolts. Tighten the 4 bolts (49)
before the 2 through-going bolts are tightened.Non-
observance of this procedure might make the jack
"3-legged".
4. Oil pedal, and grease end of pump piston.
Operation:
Lifting: Operate the pedal (14). When the
transmission jack is loaded with more than 120 kg, the
pump will automatically change over to high pressure.
This will cause transmission jack to rise a little less per
stroke.
See warning 5.
Lowering: Turn release handle (19) slowly to the left.
Maintenance:
Daily: Inspect the transmission jack for damage.
Monthly: Oil wheels and spike for pedal (17) as well as
grease end of pump piston (12). The hydraulic system
is a closed system and demands normally no mainte-
nance.
Oil: Correct oil level is just below filler plug (53) with
transmission jack in its lowest position.
Quantity of oil: 3.6 l.
Any good hydraulic oil of viscosity of ISO VG15 can be
used.
NEVER USE BRAKE FLUID!
Safety inspection
In accordance with national regulations - yet, at least
once a year - the following parts must be checked
by an expert:The lifting saddle, legs and wheels for
incipient breakage and unnormal wear. Hydraulic
parts for leaks. Function of excess-pressure valve.
Furthermore that all safety labels are legible.
Troubleshooting:
1. The jack does not lift to maximum height: Check oil
level. - See "Maintenance"
2. The jack does not stay in position: The release
handle is not properly closed - inspect distortion
of spring (20). Tighten loosely release handle (19)
and dismount it. Place hole on release handle for
screw (48) opposite to hole in valve spindle (21);
push back release handle with spring engaged with
both cylinder nut (23) and release handle, tighten
spring max. ½ turn counter-clockwise and put on
the screw.
Destruction:
When the transmission jack after several years is worn
out and must be destructed, oil must be drained off and
legally disposed of.
(Translation of original text)