Garmin AQUAMAP 10x2 Series Kurulum Talimatları Kılavuzu - Sayfa 4
GPS Garmin AQUAMAP 10x2 Series için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Garmin AQUAMAP 10x2 Series 8 sayfaları.
Ayrıca Garmin AQUAMAP 10x2 Series için: Kurulum Talimatları Kılavuzu (10 sayfalar)
Sayfayı Yazdır
Item
Wire Color
Wire Function
Violet
NMEA 0183 RxB (In -)
Orange
Accessory on
Yellow
Alarm low
Connecting the Wiring Harness to Power
WARNING
When connecting the power cable, do not remove the in-line fuse holder. To
prevent the possibility of injury or product damage caused by fire or
overheating, the appropriate fuse must be in place as indicated in the product
specifications. In addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
1
Route the wiring harness to the power source and to the device.
2
Connect the red wire to the positive (+) battery terminal, and connect the
black wire to the negative (-) battery terminal.
3
If necessary, install the locking ring and O-ring on the end of the wiring
harness.
4
Insert the cable into the POWER connector on the back of the device,
pushing firmly.
5
Turn the locking ring clockwise to attach the cable to the device.
Additional Grounding Consideration
This device should not need additional chassis grounding in most installation
situations. If you experience interference, the grounding screw on the housing
can be used to connect the device to the water ground of the boat to help
avoid the interference.
Garmin Marine Network Considerations
NOTICE
A Garmin Marine Network PoE Isolation Coupler (010-10580-10) must be
used when connecting any third-party device, such as a FLIR
Garmin Marine Network. Connecting a Power over Ethernet (PoE) device
directly to a Garmin Marine Network chartplotter damages the Garmin
chartplotter and may damage the PoE device. Connecting any third-party
device directly to a Garmin Marine Network chartplotter will cause abnormal
behavior on the Garmin devices, including the devices not properly turning off
or the software becoming inoperable.
This device can connect to additional Garmin Marine Network devices to share
data such as radar, sonar, and detailed mapping. When connecting Garmin
Marine Network devices to this device, observe these considerations.
• All devices connected to the Garmin Marine Network must be connected to
the same ground. If multiple power sources are used for Garmin Marine
Network devices, you must tie all ground connections from all power
supplies together using a low resistance connection or tie them to a
common ground bus bar, if available.
• A Garmin Marine Network cable must be used for all Garmin Marine
Network connections.
◦ Third-party CAT5 cable and RJ45 connectors must not be used for
Garmin Marine Network connections.
◦ Additional Garmin Marine Network cables and connectors are available
from your Garmin dealer.
• The ETHERNET ports on the device each act as a network switch. Any
compatible device can be connected to any ETHERNET port to share data
with all devices on the boat connected by a Garmin Marine Network cable.
NMEA 2000
Considerations
®
NOTICE
If you are connecting to an existing NMEA 2000 network, identify the NMEA
2000 power cable. Only one NMEA 2000 power cable is required for the
NMEA 2000 network to operate properly.
A NMEA 2000 Power Isolator (010-11580-00) should be used in installations
where the existing NMEA 2000 network manufacturer is unknown.
If you are installing a NMEA 2000 power cable, you must connect it to the boat
ignition switch or through another in-line switch. NMEA 2000 devices will drain
your battery if the NMEA 2000 power cable is connected to the battery directly.
This device can connect to a NMEA 2000 network on your boat to share data
from NMEA 2000 compatible devices such as a GPS antenna or a VHF radio.
The included NMEA 2000 cables and connectors allow you to connect the
device to your existing NMEA 2000 network. If you do not have an existing
NMEA 2000 network you can create a basic one using cables from Garmin.
If you are unfamiliar with NMEA 2000, you should read the Technical
Reference for NMEA 2000 Products at garmin.com/manuals/nmea_2000.
The port labeled NMEA 2000 is used to connect the device to a standard
NMEA 2000 network.
Item
Description
NMEA 2000 compatible Garmin device
GPS antenna
camera, to a
®
Ignition or in-line switch
NMEA 2000 power cable
NMEA 2000 drop cable
12 Vdc power source
NMEA 2000 terminator or backbone cable
NMEA 2000 T-connector
NMEA 2000 terminator or backbone cable
NMEA 0183 Connection Considerations
• The chartplotter provides one Tx (transmit) port and one Rx (receive) port.
• Each port has 2 wires, labeled A and B according to the NMEA 0183
convention. The corresponding A and B wires of each internal port should
be connected to the A (+) and B (-) wires of the NMEA 0183 device.
• You can connect one NMEA 0183 device to the Rx port to input data to this
chartplotter, and you can connect up to three NMEA 0183 devices in
parallel to the Tx port to receive data output by this chartplotter.
• See the NMEA 0183 device installation instructions to identify the transmit
(Tx) and receive (Rx) wires.
• You must use 28 AWG, shielded, twisted-pair wiring for extended runs of
wire. Solder all connections and seal them with heat-shrink tubing.
• Do not connect the NMEA 0183 data wires from this device to power
ground.
• The power cable from the chartplotter and the NMEA 0183 devices must
be connected to a common power ground.
• The internal NMEA 0183 ports and communication protocols are
configured on the chartplotter. See the NMEA 0183 section of the
chartplotter owner's manual for more information.
• See the chartplotter owner's manual for a list of the approved NMEA 0183
sentences that the chartplotter supports.
3