Alipa CODIPRO QLR Kullanım Kılavuzu - Sayfa 2
Endüstriyel Ekipmanlar Alipa CODIPRO QLR için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Alipa CODIPRO QLR 3 sayfaları.
Sayfayı Yazdır
Please be aware of the most common risks associated with the application of inappropriate tightening torques:
• In case of overload
o weakening of the bolt, which can lead to breakage
• In case of underload
o unscrewing of the lifting ring while pivoting
o break of the lifting ring if the base is not perfectly in contact with the load
We strongly recommend checking the tightening torque for any application.
Danger of loosening: The threaded hole and the threaded inserts muss be clean and free of defects to allow proper
assembly and tightening. Do not press the push button when the lifting ring is under load. This can cause the part to
fall off and cause serious damage.
The equipment may only be used by competent and trained personnel in accordance with the standards applicable at the place of
use.
The equipment is designed for an operating temperature between -20°C and +200°C. Avoid use in corrosive, aggressive and/or
sandy, chemical, acidic, steamy environments, ...
To mount the ring, press the push button as far as it will go to retract the inserts. Place the bolt in the threaded hole until the ring base
makes contact with the bearing surface. Then release the push button, check for complete release and tighten to secure the assembly.
Use a hexagonal socket wrench in order not to damage the clamping parts.
Before each lifting operation, make sure that the shackle is correctly oriented in the traction and that the base is
properly supported on the load. It is imperative to ensure that the ring is properly screwed and tightened, otherwise
unscrewing it may weaken the bolt and lead to material failure. Vibrations can also cause the material to unscrew.
For handling, proceed with the following steps.
• Carry out the routine checks.
• Prepare the work area for the lifting operation.
• Take into account the center of gravity (uneven weight distribution, risk of switchover, ...).
• Make sure that the ring is correctly mounted and locked:
o Mobility of moving parts
o Tight contact of the base on the bearing surface
o Push button completely released
• Hook the shackle of the ring onto a compatible lifting device.
• Apply tension carefully, then start lifting slowly.
• Make sure the mounting is balanced.
• During lifting, steering and transfer, take care to avoid collision with possible obstacles.
• Gently place the load in the prepared area.
• Remove the lifting equipment from the load.
Avoid shocks, vibrations, and dangerous maneuvers.
Plan and secure the movement to be carried out with the load.
Do not stay in a confined space between the load and an obstacle.
Avoid unnecessary contact with joints during handling.
The Working Load Limit is given in the CE declaration of conformity.
Under no circumstances may the load applied to the lifting ring exceed the WLL of the material.
The use of swivel lifting rings with an angle results in reducing the WLL coefficients. Refer to the Codipro lifting angle tables for the
calculation of these coefficients. These are theoretical and strictly indicative. It is the user's responsibility to take into account all
safety parameters before lifting. It is also the user's responsibility to ensure the dimensioning of the load. In case of doubt, a case
study can be carried out by the manufacturer.
Make sure that the users of the accessory have read and understood the contents of this instruction manual.
After use, store the ring in a clean, dry place. Take care to avoid shocks during storage and warehousing.
OPERATING PROCEDURE
WORKING LOAD LIMIT
USER TRAINING
TRANSPORTATION AND STORAGE
QLR instruction manual - translation of the French original version
Conform with the Machinery Directive 2006/42/EC
www.codipro.net - [email protected]
25, Salzbaach – LU-9559 WILTZ – Tél : +352 26 81 54 1 - Fax : +352 81 05 17
02.2021