Garmin TREAD Kullanıcı El Kitabı - Sayfa 11
GPS Garmin TREAD için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Garmin TREAD 38 sayfaları.
Ayrıca Garmin TREAD için: Kurulum Talimatları Kılavuzu (14 sayfalar)
Sayfayı Yazdır
2
Select one or more collection categories from the list.
3
Select Save.
Your collections appear as icons on the map.
Pitch and Roll
The Pitch and Roll application is intended to show vehicle
angles based on calibrated measurements only. You are
responsible for calibrating the device. Changes to the position of
the device after calibration may affect the accuracy of its
measurements. Measured values are suggestions only based
on your input into the device. Take readings often and carefully,
and allow the readings to stabilise after significant changes in
environmental conditions. Always allow a margin of safety for
changing conditions and reading errors. Failure to account for
your vehicle and your environment could cause an incident
resulting in death or serious injury.
The device alerts you if your vehicle pitches or rolls at an angle
that could affect the vehicle's stability.
Calibrating Pitch and Roll
You can set the angle of your vehicle to zero at any time.
1
Park your vehicle on a flat, level surface.
2
Adjust the position of your device in the mount so you can
comfortably view the screen.
3
Select Pitch and Roll > Calibrate.
The values for pitch and roll reset to 0 degrees.
To maintain the best accuracy, you must calibrate pitch and roll
each time you reposition your device.
Adjusting Warning Angles
You can adjust the angles at which the device activates a pitch
or roll alert. You are responsible for knowing and setting the
correct pitch and roll angle for your vehicle.
1
Select Pitch and Roll >
2
Swipe up or down to adjust the pitch or roll warning angles.
3
Select OK.
Enabling or Disabling Warning Angle Alerts
1
Select Pitch and Roll >
2
Select an option:
• To enable or disable pitch and roll notifications, select
Pitch and Roll Notifications.
• To enable or disable audible alerts, select Audible Alerts.
Viewing the Altimeter, Barometer and
Compass
The device contains internal altimeter, barometer and compass
sensors with automatic calibration.
From the main menu, select ABC.
Calibrating the compass
Calibrate the electronic compass outdoors. To improve heading
accuracy, do not stand near metal objects or objects that
influence magnetic fields, such as vehicles, electronic devices,
buildings or overhead power lines.
When your device is connected to the mount, it uses GPS data
to determine your compass heading. When you remove the
device from the mount, it uses a built-in compass to show your
heading.
Off-Road Navigation Features
WARNING
WARNING
> Warning Angles.
.
NOTICE
Each time you disconnect your device from the mount, the
device prompts you to calibrate the compass.
If you experience irregular compass behaviour, for example,
after moving long distances or after extreme temperature
changes, you can manually calibrate the compass to improve
accuracy.
1
Disconnect the device from the mount and move away from
objects that influence magnetic fields.
2
Select ABC >
> Calibrate Compass.
3
Follow the on-screen instructions.
Group Ride
The Group Ride app allows you to coordinate rides and
communicate with nearby riders using preset text messages,
live map locations and voice communications.
Starting a Group Ride
You can create a group ride that allows you to choose the group
radio channel, view and remove riders who join your group ride
and set the group ride name.
1
From the main menu, select Group Ride > Start a Group
Ride.
2
Enter your rider name and select Done.
3
If necessary, select the radio channel and select Next.
4
Enter the ride name and select Done.
As riders join your group ride, their names appear on the list.
5
Select Start.
The group ride begins after all riders sync with the group ride.
Joining a Group Ride
You can join a nearby group ride that was created by another
rider.
NOTE: for some product models, the Group Ride app is located
in the apps menu.
1
From the main menu, select Group Ride > Nearby Group
Rides.
2
Select a nearby group ride and select Join.
Rejoining a Recent Group Ride
You can rejoin any of your ten most-recent group rides.
1
From the main menu, select Group Ride > Recent Group
Rides.
2
Select a recent group ride and select Join.
Adding Riders to a Group Ride
You can add riders to a group ride that is already in progress.
1
From the main menu, select Group Ride.
2
If necessary, select
.
3
Select Add.
As new riders join the group ride, they appear on the list.
4
Select Continue.
Broadcasting a Message
Do not read, send or reply to any messages while driving. If you
do so, you could become distracted by the display, which could
lead to an accident causing personal injury or death.
You can broadcast a preset message to the members in your
active group ride that are in range of the VHF radio.
1
From the main menu, select Group Ride.
2
If necessary, select
.
3
Select Broadcast to Group.
4
Select a preset message and select Send.
WARNING
5