Garmin TREAD Kullanıcı El Kitabı - Sayfa 33
GPS Garmin TREAD için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Garmin TREAD 38 sayfaları.
Ayrıca Garmin TREAD için: Kurulum Talimatları Kılavuzu (14 sayfalar)
Sayfayı Yazdır
2
Connect the small ring end of the ground wire to the GND
terminal
on the device.
3
Connect the small ring end of the included 12-V cable to the
+12V terminal
on the device.
3
4
Tighten the
/
in. nut on the +12V terminal to a maximum
8
torque specification of 4.52 N-m (40 lbf-in.).
You should confirm the nut cannot be loosened by hand.
Do not overtighten the +12V terminal to prevent damage to
the terminal.
5
Connect the large ring end of the 12-V cable
positive terminal on the vehicle battery.
Pairing with a Garmin Navigation Device
You can pair your Garmin PowerSwitch device with a
compatible Garmin navigation device.
1
Turn on power to your Garmin PowerSwitch device and place
your compatible Garmin navigation device within 1 m (3.3 ft.)
of it.
2
On your compatible navigation device, open the Garmin
PowerSwitch app.
3
Follow the on-screen instructions to complete the pairing and
setup process.
The main app dashboard appears. After the devices are paired,
they connect automatically when they are turned on and within
range.
Garmin PowerSwitch Specifications
Dimensions (D x W x H)
Operating temperature range
Wireless frequency
Power input
Maximum accessory output
Maximum system output
Current draw with all outputs
off
Water rating
1
The device withstands incidental exposure to water of up to 1 m for up to 30 min.
For more information, go to www.garmin.com/waterrating.
Appendix
NOTICE
to the
75 x 125 x 32 mm (2.95 x 4.92 x
1.26 in.)
From -25° to 85°C (from -13° to 185°F)
2.4 GHz @ 10 dBm
From 12 to 16 V using the included
vehicle power cable.
30 A
100 A
3 mA
1
IEC 60529 IPX7
My Garmin PowerSwitch will not stay connected
• Verify the Garmin PowerSwitch device is receiving power.
• Verify that your vehicle's battery is supplying at least 12 V of
power.
The Garmin PowerSwitch device turns off automatically to
preserve your vehicle's battery if it is receiving less than 12 V.
• Verify that Bluetooth technology is enabled on your paired
navigation device or smartphone.
• Move the navigation device or smartphone closer to your
Garmin PowerSwitch device.
Wireless Cameras
Your device can display the video feed from one or more
connected wireless cameras.
Pairing the Camera with a Garmin Navigation Device
You can pair the camera with a compatible Garmin navigation
device. For more information about compatible Garmin devices,
go to the product page at garmin.com/bc40.
1
Update your navigation device to the latest software.
Your device may not support the BC 40 camera without the
latest software. For more information about updating the
software, see the owner's manual for your navigation device.
2
Install batteries in the camera.
The camera enters pairing mode automatically and the LED
flashes blue while the camera is in pairing mode. The camera
remains in pairing mode for two minutes. If pairing mode
expires, you can remove and reinstall the batteries.
3
Bring the compatible Garmin navigation device outside your
vehicle and within 1.5 m (5 ft.) of the camera and turn on the
navigation device.
The device detects your camera automatically and prompts
you to pair with it.
4
Select Yes.
TIP: if the navigation device does not detect the camera
automatically, you can select
New Camera to pair with it manually.
The device pairs with your camera.
5
Enter a name for the camera (optional).
You should use a descriptive name that clearly identifies the
location of the camera.
6
Select Done.
Viewing the Wireless Camera
This device is intended to enhance situational awareness when
used properly. If used improperly, you could become distracted
by the display, which could lead to an accident causing serious
personal injury or death. Always view the display at a glance
when the vehicle is in motion to avoid becoming distracted.
From the home screen or the map, select
Aligning the Guidance Lines
For the best reference, the guidance lines should be aligned to
reflect the outside edges of the vehicle. You should align the
guidance lines separately for each backup camera. When you
change the camera angle, you should immediately align the
guidance lines again.
1
Position your vehicle with the driver's side closely aligned to a
kerb, driveway or parking stall lines.
TIP: it can be helpful to position the vehicle in the centre of a
parking stall and then pull forward into the next stall. This
allows you to use the parking stall lines at the rear of the
vehicle as reference points for alignment.
> Wireless Cameras > Add
WARNING
.
27