Garmin GPSMAP 8600 series Kurulum Talimatları Kılavuzu - Sayfa 4
Araç Navigasyon sistemi Garmin GPSMAP 8600 series için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Garmin GPSMAP 8600 series 9 sayfaları.
Ayrıca Garmin GPSMAP 8600 series için: Kurulum Talimatları Kılavuzu (9 sayfalar), Hızlı Başlangıç Kılavuzu (6 sayfalar)
Sayfayı Yazdır
Item
Description
NMEA 2000 compatible Garmin device
GPS antenna
Ignition or in-line switch
NMEA 2000 power cable
NMEA 2000 drop cable
12 Vdc power source
NMEA 2000 terminator or backbone cable
NMEA 2000 T-connector
NMEA 2000 terminator or backbone cable
NMEA
0183 Connection Considerations
®
• See the installation instructions for the NMEA 0183 device to
identify the transmit (Tx) A (+) and B (-) wires and receive
(Rx) A (+) and B (-) wires.
• Each internal Rx and Tx port has 2 wires, labeled A (+) and B
(-) according to the NMEA 0183 convention. The
corresponding A (+) and B (-) wires of each internal port
should be connected to the A (+) and B (-) wires of the NMEA
0183 device. See the table and wiring diagrams when
connecting the data cable to NMEA 0183 devices.
• You must use 28 AWG, shielded, twisted-pair wiring for
extended runs of wire. Solder all connections and seal them
with heat-shrink tubing.
• See
NMEA 0183 Information, page 8
approved NMEA 0183 sentences that are output by and input
to your device.
• The internal NMEA 0183 ports and communication protocols
are configured on the connected Garmin device. See the
NMEA 0183 section of the chartplotter owner's manual for
more information.
• The ground wires on the NMEA 0183 data cable and your
NMEA 0183 device must both be connected to ground.
• When connecting NMEA 0183 devices with two transmitting
and two receiving wires, it is not necessary for the NMEA
0183 devices to connect to a common ground.
• When connecting a NMEA 0183 device with only one
transmitting (Tx) wire or with only one receiving (Rx) wire, the
NMEA 0183 devices must be connected to a common
ground.
• For two-way communication with a NMEA 0183 device, the
internal ports on the NMEA 0183 data cable are not linked.
For example, if the input of the NMEA 0183 device is
connected to the internal output port 1 on the data cable, you
can connect the output port of your NMEA 0183 device to
any of the internal input ports (port 1, port 2, port 3, or port 4)
on the wiring harness.
4
for a list of the
• There are four internal NMEA 0183 input ports (Rx ports),
and two internal NMEA 0183 output (Tx ports) on the
included NMEA 0183 data cable. You can connect one
NMEA 0183 device per internal Rx port to input data to your
Garmin device, and you can connect up to three NMEA 0183
devices in parallel to each internal Tx port to receive data
output by your Garmin device.
NMEA 0183 Device Connections
This diagram illustrates two-way connections for both sending
and receiving data. You can also use this diagram for one-way
communication. To receive information from a NMEA 0183
device, refer to items
,
Garmin device. To transmit information to a NMEA 0183 device,
refer to items
,
,
,
, and
device.
Item
Description
Power source
Power cable
NMEA 0183 device
NMEA 0183 cable
Item
Garmin Wire
Function
Power
Power ground
Data ground
RxA (+)
RxB (-)
TxA (+)
TxB (-)
Single-Ended NMEA 0183 Device Connections
Item
Description
Power source
Power cable
NMEA 0183 device
NMEA 0183 cable
Item
Garmin Wire
Function
Power
Power ground
Data ground
RxB (-)
RxA (+)
,
,
, and
when connecting the
when connecting the Garmin
Garmin Wire
NMEA 0183
Color
Device Wire
Function
Red
Power
Black
Power ground
Black
Data ground
White
TxA (+)
Orange/white
TxB (-)
Gray
RxA (+)
Pink
RxB (-)
Garmin Wire
NMEA 0183
Color
Device Wire
Function
Red
Power
Black
Power ground
Black
Data ground
Orange/white
N/A
White
Tx