Garmin HUD Kullanıcı El Kitabı - Sayfa 3
Araç Navigasyon sistemi Garmin HUD için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Garmin HUD 6 sayfaları. Head-up display
Ayrıca Garmin HUD için: Kullanıcı El Kitabı (14 sayfalar), Hızlı Başlangıç Kılavuzu (9 sayfalar)
Sayfayı Yazdır
Getting Started
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
Applying the Film to the Windscreen
Before applying the film to the windscreen, check all applicable
laws and ordinances in the area where you drive. Some laws
prohibit or restrict the application of film to the front window. It is
your responsibility to apply the film in compliance with all
applicable laws and ordinances. Garmin is not responsible for
any fines, penalties, or damages that may be incurred as a
result of any law or ordinance relating to the use of your Garmin
device.
Before applying the film, test the location with the device turned
on. You cannot move the film after it is applied and has dried.
Do not apply the film to a dry surface. If you apply the film to a
dry surface and try to remove the bubbles, the film will be
ruined.
You can use the included film to reflect the display onto the
windscreen.
1
Select a location to apply the film.
See the Important Safety and Product Information guide for
more information.
2
Clean and dry the windscreen with a lint-free cloth.
3
Spray clean water on the windscreen.
The water enables the film to attach to the window.
4
Pull the white tab to remove the protective layer from the
adhesive side of the film.
5
Apply the film to the window, with the protective layer with
the green tab facing out.
6
If necessary, move the film to the ideal viewing location while
the windscreen is still wet.
7
Use a card to scrape the bubbles out to the edge of the film.
Only remove the bubbles when the top protective layer is still
on the film.
The fewer bubbles under the film, the better the view of the
data.
8
Pull the green tab to remove the final protective layer from
the film.
Connecting the Reflector Lens
You can use the snap-on reflector lens instead of the
windscreen film. This allows you to use the head-up display in
other vehicles or in areas where the film is not permitted.
Snap the reflector lens onto the device.
Getting Started
WARNING
NOTICE
Connecting to Vehicle Power
You can charge a smartphone device using the USB port on the
vehicle power connector.
1
Plug the vehicle power cable into a power outlet in your
vehicle.
2
Plug the other end of the device power cable
hole on the device.
3
If necessary, plug the smartphone power cable into the USB
port
.
Placing the Device on the Dashboard
When placing the device in a vehicle, observe all placement
considerations listed in the Important Safety and Product
Information guide.
1
Select a location for the device.
2
Clean and dry the dashboard where you are placing the
device.
3
Place the device on the dashboard.
4
Press the base down.
The base conforms to the shape of the dashboard.
5
Adjust the viewing angle as needed.
TIP: Adjusting the viewing angle can also increase the
brightness of the display.
If the bottom surface of the device slides on the dashboard due
to dust and dirt buildup, wipe it clean using a cloth dampened
only with water. Do not use soap or cleaning fluids.
Connecting the Device to Your Smartphone
Before you can use the head-up display, you must connect it to
your smartphone.
1
Plug in the device and ensure it is turned on.
2
Bring the smartphone and the device within 33 ft. (10 m) of
each other.
On the smartphone, enable Bluetooth ® wireless technology
3
and search for devices.
A list of nearby Bluetooth devices appears.
4
Select the Garmin HUD in the list.
to the small
WARNING
1