Garmin ECHOMAP 60 Series Kullanıcı El Kitabı - Sayfa 27
Deniz GPS Sistemi Garmin ECHOMAP 60 Series için çevrimiçi göz atın veya pdf Kullanıcı El Kitabı indirin. Garmin ECHOMAP 60 Series 50 sayfaları.
Sayfayı Yazdır
1
Open the sonar view for which you will change the source.
2
Select MENU > Sonar Setup > Source.
3
Select the source for this sonar view.
Renaming a Sonar Source
You can rename a sonar source to easily identify that source.
For example, you use "Bow" as the name of the transducer on
the bow of your boat.
The source is renamed for the present view only. For example,
to rename the Garmin ClearVü sonar source, you must open the
Garmin ClearVü sonar view.
1
From the sonar view, select MENU > Sonar Setup > Source
> Rename Sonar Sources.
2
Enter the name.
Adjusting the Level of Detail
You can control the level of detail and noise shown on the sonar
screen either by adjusting the gain for traditional transducers or
by adjusting the brightness for Garmin ClearVü transducers.
If you want to see the highest intensity signal returns on the
screen, you can lower the gain or brightness to remove lower
intensity returns and noise. If you want to see all return
information, you can increase the gain or brightness to see more
information on the screen. This also increases noise, and can
make it more difficult to recognize actual returns.
1
From a sonar view, select MENU.
2
Select Gain or Brightness.
3
Select an option:
• To increase or decrease the gain or brightness manually,
select Up or Down.
• To allow the chartplotter to adjust the gain or brightness
automatically, select an automatic option.
Adjusting the Color Intensity
You can adjust the intensity of colors and highlight areas of
interest on the sonar screen by adjusting the color gain for
traditional transducers or the contrast for Garmin ClearVü and
SideVü/ClearVü transducers. This setting works best after you
have adjusted the level of detail shown on the screen using the
gain or brightness settings.
If you want to highlight smaller fish targets or create a higher
intensity display of a target, you can increase the color gain or
contrast setting. This causes a loss in the differentiation of the
high intensity returns at the bottom. If you want to reduce the
intensity of the return, you can reduce the color gain or contrast.
1
From a sonar view, select MENU.
2
Select an option:
• While in the Garmin ClearVü or SideVü sonar view, select
Contrast.
• While in a Panoptix LiveVü sonar view, select Color Gain.
• While in another sonar view, select Sonar Setup >
Advanced > Color Gain.
3
Select an option:
• To increase or decrease the color intensity manually,
select Up or Down.
• To use the default setting, select Default.
Sonar Recordings
Recording the Sonar Display
NOTE: Not all models support sonar recording.
1
Insert a memory card into the card slot.
2
From a sonar view, select MENU > Sonar Setup > Sonar
Recording > Record Sonar.
Sonar Fishfinder
15 minutes of sonar recording uses approximately 200 MB of
space of the inserted memory card. You can record sonar
until the card reaches capacity.
Stopping the Sonar Recording
Before you can stop recording sonar, you must begin recording
it
(Recording the Sonar Display, page
From a sonar view, select MENU > Sonar Setup > Sonar
Recording > Stop Recording.
Deleting a Sonar Recording
1
Insert a memory card into the card slot.
2
From a sonar view, select MENU > Sonar Setup > Sonar
Recordings > View Recordings.
3
Select a recording.
4
Select Delete.
Playing Sonar Recordings
Before you can play back the sonar recordings, you must
download and install the HomePort
sonar data onto a memory card.
1
Remove the memory card from the device.
2
Insert the memory card into a card reader attached to a
computer.
3
Open the HomePort application.
4
Select a sonar recording from your device list.
5
Right-click the sonar recording in the lower pane.
6
Select Playback.
Traditional, Garmin ClearVü, and SideVü
Sonar Setup
NOTE: Not all options and settings apply to all models, sounder
modules, and transducers.
From a sonar view, select MENU > Sonar Setup.
Depth Line: Shows a quick-reference depth line.
Scroll Speed: Sets the rate at which the sonar scrolls from right
to left.
In shallow water you might want to slow the scroll speed to
extend the length of time the information is displayed on
screen. In deeper water you can increase the scroll speed.
On-screen Control: Sets the behavior of the buttons on the
sonar screen control. This is available for touchscreen
devices.
Range Lines: Shows the vertical lines indicating the distance to
the right and left of the boat. This setting is available for
SideVü sonar view.
Color Scheme: Sets the color scheme of the sonar view. This
setting might be available in the Appearance menu.
The high contrast color schemes provide darker color
assignments to the low intensity returns. The low contrast
color schemes provide color assignments to the low intensity
returns that are similar to the background color.
Appearance: See
Sonar Appearance Settings, page
Overlay Numbers: Sets the data shown on the sonar screen.
Advanced: See
Advanced Sonar Settings, page
Installation: Restores the default sonar settings.
Setting the Zoom Level on the Sonar Screen
1
From a sonar view, select MENU > Zoom.
2
Select an option:
• To zoom in on the sonar data from the bottom depth,
select Bottom Lock.
• To set the depth range of the magnified area manually,
select Manual, select View Up or View Down to set the
21).
™
application and record
22.
22.
21