Alke Global-5-2FSEI Kurulum, Servis ve Kullanıcı Talimatları - Sayfa 3

Isıtıcı Alke Global-5-2FSEI için çevrimiçi göz atın veya pdf Kurulum, Servis ve Kullanıcı Talimatları indirin. Alke Global-5-2FSEI 18 sayfaları. Atmospheric stainless-steel gas infrared heaters for use in well ventilated areas

Sayfayı Yazdır

equipped with an independent manual thermostat with remote sensor (Ti = integrated sensor)

equipped with an individual solenoid valve

Ei:

equipped with an electronic ignition device (EID2G)

Ha:

adjusted for high altitude installation (>1400 meter)

Packaging

Normally (depending model and order quantity) the heaters are packed per 1, 2 or 4 in a box. Always

check the heaters for transport damage directly after receiving them. Note that the heaters will be a bit

discoloured by temperature due to a 5 minutes quality check after manufacturing.

The heaters are pre-assembled. In some cases, if there is a risk for damaging during transport, the

thermocouple sensor is separated from the gas safety device. Re-assembly can be simply done by

screwing the M8 nut of the thermocouple sensor (64-68) back on the safety device nut (55) or on EID2G

(59) for the Ei models. Do not tighten too strong.

In most cases the reflector is delivered separately from the burner part to save on transport costs.

Reassembly is easy: move the burner tube through the hole in the reflector. Slide the reflector over the

tube till it rests on the upper plate of the burner. Secure the reflector with 4 nuts M4 (17) and washers

(16).

The thermostat knob is always delivered separated from the thermostat valve.

1) Remove the plastic protection cover from the thermostat valve (sometimes already removed before).

2) Turn the knob on maximum temperature and push the knob on the valve.

3) Fix the knob by turning the large metal screw ring till it stops (at least 2 turns, hand tight).

For thermostats with a remote sensor only: bend the sensor line carefully (no sharp bends) to the

thermostat valve and secure the sensor line with a ty-rap around the red protection lining and the

thermocouple safety device (see picture). Note that the tubing is hollow, a sharp bend will close the

tubing and makes the sensor worthless. The chance of breaking the line at the entrance of the

thermostat knob is largely limited now.

Installation

Before installation, check that the local distribution conditions, nature of gas and pressure, and

adjustment of the appliance are compatible. Make sure that the gas is clean. Install a gas filter and

condensate trap before the heaters in case the gas is dirty or wet/oily. No guarantee can be given on

heaters operating on gas that is not clean.

Dimensions

Physical dimensions of the appliances (rounded values)

Model

Global-5 / Global-10

Global-5-T / Global-10-T

Global-5-2F / Global-10-2F

Global-5-2FT / Global-10-2FT

Global-5-S / Global-10-S

Global-5-2FS / Global-10-2FS

Global-5-Ei / Global-10-Ei

Global-5-2FEi / Global-10-2FEi

Global-5-SEi / Global-10-SEi

Global-5-2FSEi / Global-10-2FSEi

Global-5-2FDi

Version: Sept 2017

Length (cm)

Width (cm)

59 / 69

42 / 61

64 / 74

42 / 61

59 / 69

42 / 61

64 / 74

42 / 61

67 / 77

42 / 61

67 / 77

42 / 61

60 / 70

42 / 61

60 / 70

42 / 61

65 / 75

42 / 61

65 / 75

42 / 61

Height (cm)

Weight (kg)

25 / 25

2,0 / 3,3

31 / 31

2,4 / 3,7

25 / 25

2,2 / 3,5

31 / 31

2,5 / 3,8

26 / 26

2,4 / 3,7

26 / 26

2,5 / 3,8

31 / 31

2,7 / 4,0

31 / 31

2,8 / 4,1

31 / 31

2,9 / 4,2

31 / 31

3,1 / 4,4

2,3

manual number: 0009 0440EN