Garmin GPSMAP 4012 - Marine GPS Receiver Kurulum Talimatları Kılavuzu - Sayfa 2

Deniz GPS Sistemi Garmin GPSMAP 4012 - Marine GPS Receiver için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Garmin GPSMAP 4012 - Marine GPS Receiver 19 sayfaları. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Ayrıca Garmin GPSMAP 4012 - Marine GPS Receiver için: Kullanıcı El Kitabı (2 sayfalar), Teknik Referans (30 sayfalar), Hızlı Referans Kılavuzu (2 sayfalar), Kurulum Talimatları Kılavuzu (25 sayfalar), Kurulum Talimatları Kılavuzu (25 sayfalar), Hızlı Referans Kılavuzu (2 sayfalar), Önemli Güvenlik Bilgileri (48 sayfalar), Uygunluk Beyanı (1 sayfalar), Şablon Kılavuzu (2 sayfalar), Ek Kılavuz (24 sayfalar)

Sayfayı Yazdır
Garmin GPSMAP 4012 - Marine GPS Receiver Kurulum Talimatları Kılavuzu
To install the bail mount and unit:
1. Using the bail mount as a template, mark the location of the four mounting holes. Be sure to leave at least 5" (12.7 cm) of clearance
behind the unit for the wiring.
NoTE: Mount a 4008/4208/5008/5208 unit 31
2. Using an appropriately sized drill bit, drill the pilot holes for your mounting hardware.
3. Secure the bail mount to the surface with your mounting hardware.
4. Loosely attach the mounting knobs to the GPSMAP 4000/5000 series unit.
5. Slide the unit onto the bail mount, and tighten the mounting knobs.
Flush Mounting the GPSMAP 4000/5000 Series Unit
Hardware (included):
• Flush mount template
• Four threaded 4 mm mounting studs
• Four 4 mm flat washers
• Four 4 mm lock washers
• Four 4 mm nuts
Tools required (not included):
• Jig saw
• Masking tape
• Scissors
• Drill
• Drill bits—
3
/
" (6 mm) and 4 mm
8
•
/
" (2 mm) Allen (Hex) wrench
1
16
• 4 mm sockets or wrenches
• Center punch and hammer
/
" (80 cm), and a 4012/4212/5012/5212 unit 39
1
4
GPSMAP
Pilot Hole
3/8" (9.5 mm)
6 17/32"
(165.90 mm)
Flush Mount Template Example (not to scale)
July 2007
190-00779-03_0B.indd 1
" from a magnetic compass to avoid interference.
/
3
8
4000 SerieS FluSh Mount teMPlAteS
®
GPSMAP 4008/4208
unit dimensions: 11 3/16" (284.4 mm) wide x 6 31/32" (176.9mm) high
Cut on
thiS line
9 5/8" (244.50 mm)
190-00779-03 Rev. B
GPSMAP 4000/5000 Series Installation Instructions
USE 4 mm DRILL BIT
Recommended clearance
for SD card door
1/2"
13 mm
Printed in Taiwan
7/9/2007 10:08:51 AM