Garmin GPSMAP 5008 - Marine GPS Receiver Kurulum Talimatları Kılavuzu - Sayfa 2

Deniz GPS Sistemi Garmin GPSMAP 5008 - Marine GPS Receiver için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Garmin GPSMAP 5008 - Marine GPS Receiver 25 sayfaları. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Ayrıca Garmin GPSMAP 5008 - Marine GPS Receiver için: Hızlı Referans Kılavuzu (2 sayfalar), Kullanıcı El Kitabı (2 sayfalar), Kullanıcı El Kitabı (2 sayfalar), Teknik Referans (30 sayfalar), Kurulum Talimatları Kılavuzu (19 sayfalar), Kurulum Talimatları Kılavuzu (25 sayfalar), Hızlı Referans Kılavuzu (2 sayfalar), Önemli Güvenlik Bilgileri (48 sayfalar), Uygunluk Beyanı (1 sayfalar), Baskı Kılavuzu (2 sayfalar), Ek Kılavuz (24 sayfalar)

Mounting the GPSMAP 4000/5000 Series Chartplotter

You can mount the GPSMAP 4000/5000 series chartplotters one of two ways. You can use the included bracket to bail mount the chartplotter, or

you can use the included template and hardware to flush mount the chartplotter.

You cannot bail mount the GPSMAP 5015/5215 chartplotters. Because of the larger size, you must flush mount the GPSMAP 5015/5215 chartplotters.

Bail Mounting the GPSMAP 4000/5000 Series Chartplotter

Use the included bracket to bail mount the GPSMAP 4000/5000 series chartplotter.

tools required (not included):

• Drill and drill bit

• Screwdriver

• Pencil

• Mounting hardware (screws or nuts, washers, and bolts)

NOTE: The mounting hardware (screws or nuts, washers, and bolts) are not included. The holes on the bail mount are 5/16 in. (7.9 mm) in

diameter. Choose mounting hardware that fits the holes in the bail mount and securely attaches it to your specific mounting surface. The size

of the drill bit required depends on the mounting hardware chosen.

to install the bail-mount bracket:

NOTE: You cannot bail mount the GPSMAP 5015/5215 chartplotters. Because of the larger

size, you must flush mount the GPSMAP 5015/5215 chartplotter.

1. Using the bail mount as a template, mark the location of the four mounting holes. Be sure to

leave at least 5 in. (12.7 cm) of clearance behind the 4000/5000 series chartplotter for the

wiring.

NOTE: Mount a GPSMAP 4008/4208/5008/5208 chartplotter 31 1/2 in. (80 cm), and a

GPSMAP 4010/4210/4012/4212/5012/5212 chartplotter 39 3/8 in. (1 m) from a magnetic

compass to avoid interference.

2. Using an appropriately sized drill bit, drill the pilot holes for your mounting hardware.

3. Secure the bail mount to the surface with screws and washers.

to install the GPSMAP 4000/5000 series chartplotter on the bail-

mount bracket:

1. Loosely attach the mounting knobs to the GPSMAP 4000/5000 series

chartplotter.

2. Slide the chartplotter onto the bail mount, and tighten the mounting knobs.

notice

Mounting

screws

Bail-mount

bracket

Mounting knobs ×2

GPSMAP 4000/5000 Series Installation Instructions