Garmin GPSMAP 5015 Kurulum Talimatları Kılavuzu - Sayfa 4

Deniz GPS Sistemi Garmin GPSMAP 5015 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Garmin GPSMAP 5015 25 sayfaları. Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Ayrıca Garmin GPSMAP 5015 için: Hızlı Referans Kılavuzu (2 sayfalar), Kullanıcı El Kitabı (2 sayfalar), Kurulum Talimatları Kılavuzu (25 sayfalar), Hızlı Referans Kılavuzu (2 sayfalar), Güvenlik ve Ürün Bilgileri (48 sayfalar), Teknik Referans (42 sayfalar), Ürün Bilgileri (48 sayfalar), Uygunluk Beyanı (1 sayfalar), Sıva Altı Montaj Şablonu (2 sayfalar), Ek Kılavuz (24 sayfalar)

Garmin GPSMAP 5015 Kurulum Talimatları Kılavuzu
Flush Mounting a GPSMAP 4008/4208/4012/4212/5008/5208/5012/5212 Chartplotter
Flush Mounting a GPSMAP 4010/4210 Chartplotter or a GPSMAP 5015/5215 Chartplotter:
Hardware (included):
• Flush-mount template
• Rubber gasket
• Mounting screws (4.2 × 1.4 DIN7981 / number 8 ANSI)
to flush mount a GPSMAP 4010/4210 chartplotter or a GPSMAP 5015/5215 chartplotter:
1. The flush-mount template is included in the product box. Trim the template and ensure it will fit in the location where you want to flush mount
the chartplotter.
NOTES:
• Make sure the surface on which you mount the chartplotter has at least 7 in. (18 cm) of open space behind it to fit the chartplotter and the
connected wires, and make sure to leave approximately 1/2 in. (13 mm) of space on the right side of the chartplotter to access the SD card
door.
• Mount a 4010/4210 chartplotter 31 1/2 in. (80 cm), and a 5015/5215 chartplotter 23 5/8 in. (60 cm), from a magnetic compass to avoid
interference.
2. The flush-mount template has adhesive on the back. Remove the protective liner and apply
the template to the location at which you want to mount the chartplotter.
3. Using a
/
in. (10 mm) drill bit, drill a pilot hole inside the corner of the template to begin
3
8
cutting the mounting surface.
4. Using the jigsaw, cut the mounting surface along the inside of the solid line indicated on the
flush-mount template. Use a file and sandpaper to refine the size of the hole.
5. If the top and bottom mounting covers are attached to the front of the chartplotter, remove
them by unsnapping the covers from the sides.
4
Chartplotter
Mounting studs ×4
Rubber gasket
Mounting surface
Lock washers ×4
Flat washers ×4
Hex nuts ×4
tools required (not included):
• Jigsaw
• Masking tape
• Scissors
• Drill
• Drill bits—
/
in. (10 mm)
3
8
• Center punch and hammer
• Anti-seize lubricant (optional)
Mounting covers ×2
GPSMAP 4000/5000 Series Installation Instructions